|Product Type||Shipped Product|
|Number of reviews||0|
BBC CHEVY 454/468 COMPLETE ENGINE HYDRAULIC ROLLER CAM 530 HP
RUNS ON PUMP GAS.
This engine is fully assembled from intake to oil pan.
The engine shown above is an actual representation of the engine you will receive with the exception of the polished intake. This engine includes a satin finish intake. The polished intake is an upgrade option. See the option list below.
Our engines can also be built for use in marine applications. Pictured below is one of our bbc engines in a customer's boat.
We also offer our engines with a lower cost basic front accessory kit, with electric water pump option and with no turn-key options at all (base engine). See all our engine listings. We also offer our bbc engines setup with a blower as pictured below.
DART BIG M BLOCK WITH SPLAYED MAIN CAPS.
WISECO PISTONS, SCAT CRANK, AND SCAT RODS. PC ALUMINUM HEADS.
4.310" BORE X 4.00" STROKE
- NEW DART BIG M BLOCK WITH SPLAYED MAIN CAPS.
- PROCOMP ALUMINUM ALLOY HEADS.
- COMP HYD. ROLLER CAM AND HOWARDS TIE BAR STREET STRIP ROLLER LIFTERS.
- SA GEAR BILLET TIMING SET WITH TORRINGTON BEARING AND ROLON CHAIN 9 KEYWAY. TOP OF THE LINE.
- COMP ULTRA PRO MAGNUM ALUMINUM ROCKERS 1.7 RATIO.
- SCAT CRANKSHAFT, CLEVITE BEARINGS. BALANCED ON OUR CWT BALANCER TO BELOW 2 GRAMS.
- SCAT COMPETITION RODS WITH ARP 8740 CAP SCREWS.
- WISECO PREMIUM FORGED PISTONS. 800+HP RATED.
- MELLING M-SELECT SERIES OIL PUMP WITH M-SELECT DRIVE ROD.
- CHAMP CUSTOM OIL PAN WITH OIL CONTROL SYSTEM.
- PRO-RACE BRAND DAMPER.
- TWO YEAR WARRANTY.
Pump gas friendly.
Our 454/468 Hydraulic Roller cam engine will produce 600 horse power at approx. 5800 rpm. The build sheet is at the lower part of this listing. This engine is an excellent choice for use in classic street rods, sport trucks, 4x4 trucks, and can be used as a daily driver. High mileage use is not a problem with this engine. This is engine may also be setup for use in larger work trucks, or motor homes. We can also set any of our engines up for marine use.
This engine will produce more than double the horse power of the original bbc 396, 427 and 454's and much greater torque. Pump gas friendly. For those wanting to put this engine in a classic car or sport truck, select cam choice # 1 or # 2 with the Hurricane intake. This engine will deliver very impressive power in the lower rpm range, and have a very high degree of drivability and long life.
See our other listings for the fully dressed out turn-key version.
This engine size is not the best value for the money compared to our other bbc engines. We use a brand new Dart Big M block on several of our bbc engines. It would be more practical to move to the next size, (505) since it's the same price as this engine, but moving up two steps to the 555 is actually the way to go. The 555 uses a new Merlin IV block.
The 555 engine gains a huge jump in hp and torque over the 468 and the 505 due to fact it has a wider bore. This wider bore makes the 555 a very efficient engine. Look closely at the dyno reports, and notice the difference in torque and hp throughout the rpm range. Same heads and cam in the 555 yields amazing power over the 468 and the 505. Efficiency is the key in the 555. The wider bore un-shrouds the valves and allows the cylinder heads to work at peak efficiency. There are no drawbacks to moving up in engine size. The Merlin IV block still has several rebuilds left in it even with the 555 engine. Engine longevity and reliability are not affected in any way.
Two year warranty, see details below.
This engine is designed to have a high level of drivability, or street manners. Cams #3 and #4 are our favorites for offering exceptional low end and mid range performance plus max drivability without needing to deepen final gearing or the need for a high stall speed torque converter.
If you choose to go with the Hurricane single plane intake and the first choice cam, it will bring the hp numbers up to approx. 600. We do not recommend the single plane intake combined with cam choice 1 on any car that is over approx 3,200 lbs and/or cars with a steep (tall) final gear.
Please read the cam info provided below on the four cam choices before purchasing this engine. It is very important that you choose the correct cam and intake for your car and its intended purpose.
Here are a few good reasons why we think the 454 engine is a better choice than the stock GM bbc engine.
1. The 454 will accelerate any heavy car much better than any of the underpowered original GM bbc engines.
2. The exhaust note from this big block engine is much deeper than that of the typical stock GM big block engines.
3. Installing this engine in heavy cars or trucks without killing acceleration, or having to deepen the final gear, and needing a huge stall converter is a real plus. This engine will accelerate a 7500 lb vehicle much better than any stock bbc engine.
4. Low maintenance and high drivability even in very heavy cars and trucks, while generating up to 600 hp at the same cost as building a 454 stock engine.
5. Longevity and reliability. You don't have to turn the engine to a critical rpm range to produce its max hp output. There's nothing unsafe about running an engine that's well built like this up to 5,800 rpm. The hydraulic roller cam is very reliable and will not require a bronze distributor gear, as it has a normal cast gear. Our aluminum heads use very high quality hardware. All of our valves are from PBM, and are considered to be very high quality valves.
6. Should you ever decide to sell your car, or truck with this engine, the resale value would be much greater.
We do a full test run on every engine we build on a test mule. The engine is run for two intervals of 15 minutes each, and every possible issue is addressed. When you install the engine, you must verify that the timing is set at the correct value, and the fuel to air ratio must be verified. We also include an engine stand like the one pictured, wheels included, and an engine lift plate.
De-tuned engines with different cam and intake combos will move the torque into the low rpm range, and is very desirable if you're sporting around on the street, rather than all-out racing. The de-tuned version of this engine will also allow you to set the car up closer to stock and increase drivability to a very high degree. Throttle response is also noticeably better. We can help you with a cam and intake selection that best suits your needs.
The build sheet is as follows:
This is a file photo. Appearance may vary.
We have various bore sizes available.
Dart Block Specs. and features.
- Standard 9.800" deck ht.
- Siamesed extra thick cylinder walls to resist cracking and improve ring seal (minimum .300" thick with 4.625" bore).
- Uses +.300" tall Gen VI style lifters.
- Scalloped outer water jacket walls improve coolant flow around the cylinder barrels to equalize temperatures.
- 4 bolt ductile iron main caps have splayed outer bolts for extra strength.
- True priority main oil system lubricates the main bearings before the lifters.
- Oil filter pad is drilled and tapped for an external oil pump.
- Lifter valley head stud bosses prevent blown head gaskets.
- Rear main cap uses standard oil pump and two piece seal - no adapter required!
- Mechanical fuel pump boss, clutch linkage mounts, and side and front motor mounts simplify by Vid-Saver">installation in any chassis.
- Dual oil pan bolt patterns fit standard and notched oil pans.
The block is bored to size with our new Centroid touch probe machine. Few machine shops have a machine of this accuracy.
We also deck the blocks to an RA finish of approx. 15 or better. The decking procedure is also done by our Centroid CNC machine.
We often find many brand new blocks to have a sloping deck of up to 4 thous. When we're finished decking the block, it is within approx. .001 accuracy from end to end. Many machine shops fail to catch this as the machinery they use does not allow for such accuracy.
We then plate hone the block with our new Sunnen SV10 diamond hone machine. This is also a very advanced machine that hones the block with a finish unlike conventional machines.
The final step is to clean the block in our high pressure block washer.
Pictured below is the rotating assembly that comes in this engine.
(file photo, actual parts may vary, see details below)
The photos above and below are file photos. Actual appearance may vary. This picture is to give you an idea of parts used in the rotating assembly portion of this engine. All parts are brand new, first line, unblemished, and balanced in house.
READ THIS LISTING COMPLETELY BEFORE YOU BUY ELSEWHERE!
Connecting Rod Specs.
Piston & Ring Specs.
Bearing, Damper, and Flexplate Specs.
Listed below is a complete breakdown of all the parts that are included in this engine.
WISECO FULLY FORGED PISTONS, RATED AT 800+ HP. WISECO PISTONS ARE 100% MANUFACTURED IN THE USA. THEY ARE ONE OF THE HIGHEST RATED PISTON BUILDERS IN THE COUNTRY.
The Wiseco forged pistons are rated very high in the street/strip performance industry. They
are made using the 2618 aircraft alloy and have fully machined crowns. We prefer the 2618 alloy over the lower cost 4032 alloy. This alloy may fragment from the effects of detonation and if this happens, it can be very destructive to the engine.
Those types of pistons are fine for stock or mild engine builds, but should never be used in carbureted engines built to high horse power levels.
The forged 2618 alloy piston is much more resistant to the effects of detonation and heat.
Our Wiseco Forged pistons are custom designed with an increase in compression height. This has many advantages. Here are a few facts about compression height and deck height.
Our custom made pistons have a compression height that is .010 taller on bbc pistons, and .015 taller on sbc pistons, as compared to most all of the catalog pistons on the market. We find this to be a very valuable feature.
Since our pistons sit at a taller than normal compression height, we only have to remove approx. .005-.010 off the deck surface of the block. Our goal is set the piston at zero deck (flush with the deck surface). This maintains the deck's thickness, making it much stronger than a block that has been cut down .025. The engine will also run a bit cooler with a thicker deck. It's well known that the deck dissipates much of the built up heat an engine generates. This also allows for future deck re-surfacing without compromising the integrity of the block. On our bbc engines, we actually leave the piston about .003 to .005 in the hole to allow for possible piston rock. Our sbc engines will have the pistons setting right at zero with the deck.
You may have noticed that our Wiseco custom made forged pistons are referred to as Racing Pistons on the package. This does not mean that the pistons are for racing only. This is a generic term, referring to their ability to be used in high performance applications as well as for street rod use. These pistons are perfectly designed for use on the street, as well as for medium to upper level drag racing.
We have built approximately 5000 engines using the Wiseco pistons. The engines have been for street rod and strip use. We have seen no problems, nor have there been any complaints. They are an excellent product in every respect.
These pistons are also suitable for use with nitrous or blower setups.
The picture below is a file photo of our Wiseco pistons.
MAHLE HIGH PERFORMANCE MOLY RINGS
The picture below is a generic file photo of a Scat crankshaft.
Some of the benefits of the Scat crankshaft supplied with this assembly:
The material used in this crankshaft is manufactured from an exclusive Space Age material that was designed for high strength and fatigue resistance. The Scat cranks are the best value you will ever find. The Scat crankshafts are the best way to build a strong bottom end for, street rods, dirt and circle track racing, and drag strip racing. This crank is suitable for use up to approx. 600-650 hp.
Pictured below is our ABS crank polishing machine in action. We polish the crank on every engine we build. This extends bearing life, keeps oil cooler, and with the reduced friction, a slight increase in horsepower is gained. Many machine shops fail to do this. The finish on most cranks are at the bare minimum of acceptance, and we know this can affect bearing life. We have measured the RA finish with our profilometer, and found it to be as high as 25 RA finish on many of the cranks. We bring that number down to below considerably.
We now use the Clevite bearings in our engines.
Our choice of rods are the SCAT COMPETITION SERIES rods with ARP-8740 cap screws.
The Scat Pro-Comp extreme duty I-beam rods should not be mistaken for ProComp rods. These rods are made exclusively by Scat, and have nothing to do with the ProComp company. The critical sizing and installation of the ARP cap screws is performed on a Sunnen machine in the USA by Scat Industries. These rods are excellent for those wanting the extra security offered by a rod with 7/16 ARP cap screws.
Take notice of the design of these rods. They are far superior to conventional style I-beam rods.
If you do a search on the Scat Pro-Comp rods, you will find a vast amount of info on many car forums. All of the info is 100% positive. These rods are run in engines that not only produce high horsepower levels, but also run at continuous RPM. Notice the general appearance in the pictures. These rods do look impressive. The style is reminiscent of a steel billet rod.
The fact that these rods are incredibly strong and well made, coupled with the fact they are light weight, made it an easy decision to use them in all of our high horsepower street/strip engines.
We have noticed some engine builders using low cost generic rods and crankshafts in their engines. These non-branded, (no-name) products are often poor quality in many ways. You will notice many of the low end engine builders fail to mention the actual brand of the rods or cranks used in their engines. Upon further investigation you will find such parts not to be a branded name product. They may label these parts with a name, but one that is totally unrecognizable in the industry. Our experience in years past with such rods and cranks has been disappointing to say the least. Besides the obvious issues such as incorrect sizing and machining that is difficult to correct, the questionable alloy these items may be produced from and the potentially incorrect heat treating methods used, could prove to be disastrous. Little can be done to verify this and nothing can be done to correct it. Failures of such critical parts will usually result in catastrophic damage to the engine. As you may have noticed, this is why we specify the brand name, and series of every part used in our engines.
Many of the inferior "no-name" rods on the market will also have "no-name" rod bolts in them. We have seen these bolts before, and they are very low quality. They don't have ARP's rolled thread design, and they don't torque down with the same characteristics as a genuine ARP bolt. It's not just a matter of having a different brand bolt in the rods; these bolts are low quality in many ways. They have been known to fail in engines to a much greater degree than a high quality rod bolt, and this failure usually causes catastrophic damage in the engine. Beware of rods that don't mention the rod bolt brand. As far as we're concerned, ARP bolts are the only brand we would ever use or accept in a set of rods.
Genuine ARP 8740 cap screws.
Our CWT 5500 Balancer.
We do our own balancing with our new state of the art CWT 5500 Series balancers. The CWT 5500 is the ultimate for precision balancing. We now have three of these in our machine shop. We consider this machine to be highly advanced compared to the Hines balancer we once used. We balance every rotating assembly we sell within 2 grams or less at no extra charge. A balance sheet is included with your assembly.
Three CWT balance machines under one roof is a rare sight.
Our crew wrapping up for the day. Pardon the mess.
Our Procomp bbc heads are used on many of our bbc engines.
PC aluminum heads with 300cc runners, 119cc combustion chambers, 2.250/1.88 stainless PBM valves, 1.46 diameter Melling dual roller springs. These cyl. heads are made by Procomp. We use our own hardware and do our own assembly.
Here is a rundown on the hardware we are using in the bbc Procomp heads.
PBM Competition Series Stainless Valves.
NON MAGNETIC stainless steel PBM Competition Series valves, swirl finished one piece, undercut and backcut. We have used the same valve for years, with zero failures. Non magnetic is very important. Our cost on these valves is around double the price of some low cost valves on the market. We sell these valves for just under $200 in our other listings. They are the only grade of valves we use in our bbc heads. Many head builders use the low cost valves, but we do not use them and never will. If the valves pull a magnet, they are not high temp stainless. They may be stainless, but they have very low nickel content in them.
We have dynoed at least 300 engines with the Procomp heads and they performed faultlessly. We have never experienced failure of any kind with the Procomp bbc heads. See important article concerning the PC heads at the bottom of the ad.
Fel Pro 1017 premium race grade series head gaskets, ARP head bolts, and rocker studs.
ARP HEAD BOLTS AND WASHERS AND ROCKER STUDS.
COMP ULTRA PRO-MAGNUM ROCKERS.
The new Ultra Pro Magnum™ Roller Rocker Arms not only live up to the lofty standards of the original Pro Magnums™, but they also take stud mount rocker performance, stability and value to a whole new level. The modern arched, web-like design delivers increased strength and rigidity while still reducing the moment of inertia and optimizing the dynamic balance.
Premium Morel Hydraulic Roller Lifters.
We use Howards brand premium pushrods in all of our engines. They are lightweight in design, yet very strong. Made in the USA from 4130 chromoly steel. Regular hardened pushrods will most likely flex in the engine when running above normal RPM ranges, and risk bending under high RPM. These do not have the welded ball on the end. We only use the swedged one pc. design, which is a well proven design far superior to the style many others use in engines. 4130 chromoly steel is also much stronger, and will resist flexing. When a pushrod flexes in the engine, you lose lift. Don't be misled by the term "hardened," as this is nothing more than a stock style low cost push rod. They will flex in the engine or possibly bend permanently.
Our choice of lifters are the Howards brand tie bar lifters. These lifters have many unique features.
Pictured below is our Speedmaster single plane intake. We also offer the Edelbrock satin RPM Air Gap intake as an alternate choice at no extra charge.
304 STAINLESS ALLEN HEAD INTAKE BOLTS ARE USED ON ALL OUR ENGINES.
We are offering two cam choices listed below in this engine. Read the specs carefully.
Cam Choice # 1 By Comp Cams.
Part number: 01-456-8
112 lobe sep.
Peak advertised hp of 600 would come in around 6100 rpm. A 2750-3000 stall converter is recommended for better acceleration when using this cam and a final gear of 3.55 or numerically higher. With our single plane intake, this cam will achieve the advertised horse power. Cam lope is radical at idle. Street manners are not this cams strong point. Vehicles weighing over 4250 should not use this cam choice.
Cam Choice # 2 By Comp Cams.
Part number: 01-451-8
112 lobe sep.
Cam choice # 2 offers increased drivability and improved low end power, with very little sacrifice of the max power as compared to cam choice # 1, a 15-20 hp decrease at the most. The torque numbers will remain nearly the same and come in approximately 150 rpm lower compared to cam choice # 1. Valve train stability and longevity is increased with this cam. This cam is recommended for use in light to medium weight vehicles with tall gearing, and sport trucks. Max power will be achieved at approx. 5850 rpm. You may use the single plane intake with this cam and not affect the low end power to any noticeable amount.
By using cam choice # 2, your valve train will be much more reliable and longevity is certainly improved. Cam choice # 2 will allow you to run a stall converter in the 2500-2750 rpm range. Final gearing when used in a car or sport truck could actually be in the 3.55 range or even taller, and overdrive use may be possible. Mileage with taller gearing is also a plus. This cam would be most suitable in heavy vehicles weighing up to 4500 lbs. Drivability with this cam is fair to decent depending on your vehicle weight and final gearing. This cam may not develop enough vacuum to operate power brakes.
We have several different options in valve covers. Here are our most popular choices:
These are just a few of our popular valve covers you may choose from. We do have several more choices to select from in our other listings at no additional cost.
If you chose cam choice 1 or 2, then we highly recommend using an exhaust evac. system. The vacuum created by the engine is somewhat insufficient when using these larger cams, heads, carb and intake to operate a pcv system at its best. The exhaust evac system will pull the crankcase gases out of the engine at a very smooth and controlled rate. This allows the rings to seat in much faster and better, and can increase horse power to some degree by reducing crankcase pressure. Another benefit of the evac system is that you're not contaminating the fuel and air mixture with semi-burned byproducts from the engine oil and combustion process.
After the engine is completely broken in, the pcv setup may be sufficient. However, it may not be the best choice. The break-in time may also be slower with the pcv setup.
We also offer a vacuum pump system for the ultimate in crankcase pressure control.
If you do decide to use an exhaust evac system, we have a few more recommendations. The bullet style perforated mufflers, like those made by Magnaflow and many other companies, must be used. In our opinion, they sound the best and, most importantly, they allow the exhaust evac system to work properly. Magnaflow is a popular brand of the true straight through mufflers, and there are several other brands on the market such as Corsa, Borla, and Bullet. The sound level is controlled by the length you choose. The 12-16 inch length sounds the best to us. These mufflers have smooth perforated inner walls. They should not be confused with traditional glass packs with fluted walls, which are very restrictive and have a somewhat sloppy sound.
Traditional chambered mufflers, like Flowmaster, create a back pressure pulse that will interfere with the operation of an exhaust evac. system. Chambered mufflers have the reputation of helping bottom end throttle response, but you will have a decent amount of bottom end power with this engine, especially if you have chosen cam choice 2, 3 or 4. In our experience, the straight through perforated mufflers sound and perform better in every respect, and allow the proper use of an exhaust evac. system. More info. on this subject below.
Timing components: SA Gear 8999T billet double roller timing set.
Polished Aluminum Timing Cover.
We use the top of the line SA Gear timing set with a torrington bearing and rolon chain. The difference in quality is dramatic compared to the common low-cost timing set. The upper sprocket is made from billet steel and the lower is induction hardened with nine keyways. These sets are hand matched for selective sizing.
The cost on this high end timing set is approx $97.50, more than double the cost of the low level budget timing set used by many other engine builders. Should you ever want to confirm that this is what is actually in your engine, you can remove the timing cover, and you will see that this timing set is very different in appearance to the run of the mill low cost sets often used by others.
This timing set is offered in three different chain tension setups, allowing us to set it up perfectly every time. One more benefit is that timing accuracy is very precise and will remain that way. This timing set will likely last for the life of the engine. This is what you will find in most solid roller engines, as they have very high spring rates, and create an enormous load on the chain and gears, compared to non solid roller setups. It may seem like a bit of overkill to use such a high end timing set, but the versatility and extreme quality outweigh the cost, in our opinion.
Champ premium oil pan.
The oil pans we use on all of our engines are made in the USA by Champ. The Champ oil pan has a full windage tray, crank scraper, and trap door. Threaded dipstick is included. Extreme duty pickup designed not to fail. The oil pan is made from a thicker than normal gauge material, and has embossed ribs in the body.
If your engine is equipped with the 7 qt. Champ oil pan, it has kickouts that swell outward approx. 3 inches on each side. If you think you will encounter clearance issues with the kickouts, we recommend opting for the stock appearing 5 qt. oil pan. The 5 qt. pan will still be a Champ pan and will have the windage tray and crank scraper. We strongly recommend reducing the amount of oil used in these oil pans by approx. 1/4th of a quart. Doing this may reduce the chance of oil leaks and reduce oil temps. The larger counter weights used on stroker crankshafts are why we recommend reducing the oil capacity in these engines. The higher capacity 7 quart oil pan is an optional upgrade on some of our engines.
To be clear on what we're saying, we would like to see you add right at 7.0 to 7.5 quarts of oil grand total in your engine and oil filter when using the higher capacity oil pan that has the flat ribbed bottom with kickouts on the side. When using the stock appearing oil pan, we would like to see you add right at 5.5 to 5.75 quarts grand total in your engine and oil filter.
Our engines include a dipstick. It's very important that you re-calibrate the oil level marking on the dipstick. This is due to the fact that the dipstick, oil pan, and block are all made from various manufacturers and we often see great variances. Couple this with the fact that you may be running a reduced amount of oil, and the "full" mark on the dipstick will most likely not indicate correctly. Once you have put a predetermined amount of oil in your engine, and run it for a few minutes, let it sit for awhile on level ground, check the oil, and mark your dipstick with a flat file to re-establish the full mark.
We do not use the knock off oil pan gaskets on the market. Felpro premium oil pan gaskets are used on all of our engines.
Pictured below is a file photo. The actual Felpro gasket used will be the correct model for this application.
Studded Mini Nut Set.
We use our premium studded mini nut set on all of our oil pans and valve covers. The nuts have a serrated face and built in washers. This is the ultimate set for securing the oil pan and valve covers to the engine and is far superior to the typical bolts used by most other engine builders. Our standard engine color is black. Custom paint work on engine blocks and oil pans is available as an optional upgrade. The pictures above and below are file photos to display the studded mini nuts. Other items seen in these pictures may not represent your actual engine.
Melling M-Select Oil Pump, and M-Select Drive rod with ARP stud.
The M-Select series oil pump by Melling has several important upgrades compared to the regular Melling M-55 Series. The gears are billet steel, and the body is stronger, coated with corrosion-resistant nitrite. This oil pump also includes the M-Select drive rod. Both components are far superior to the regular Melling oil pump and drive rods used by most other engine builders.
We include an engine lift plate and heavy duty engine stand with casters with every engine we build.
This product does not have any reviews yet.