Skip White Performance - We have the best prices you will ever find for aluminum heads, rotating assemblies and strokers
Skip White Performance
1910 Brookside Lane
Kingsport, TN 37660

M-F 8a-7p EST
Sat 10a-3p EST

5 star rating
272,950+ reviews!

 423-722-5152

CHEVY BBC 540 555 STAGE 7.0 TURN KEY ENGINE, NEW WORLD MERLIN IV BLOCK, 724 hp

Available

$8,595.00



Product Information

UPC371537392123
Product TypeShipped Product
Shipping Cost $485
Number of reviews 0
BBC CHEVY HYDRAULIC ROLLER CAM EXTREME TORQUE
TURN KEY 540/555 CUBIC INCH ENGINE 724 HP

THE NEW BBC TURNKEY ENGINE WITH A CVF V-BELT SYSTEM photo b4cde475-8710-46e5-8ec7-db8a85702020.jpg

RUNS ON PUMP GAS. WISECO FORGED PISTONS AND SCAT COMPETITION SERIES RODS, MERLIN IV BLOCK, BRAVO ALUMINUM HEADS
335cc RUNNERS.

This engine comes fully dressed out on the front as pictured above. The carb, distributor, wires and starter are not included with this engine. We have those items available in our other listings.

FULLY ASSEMBLED FROM INTAKE TO OIL PAN

Our 540/555 Hydraulic Roller cam engine will produce 724 horse power at approx. 5900 rpm. The build sheet is at the lower part of this listing. This engine is an excellent choice for use in classic street rods, sport trucks, 4x4 trucks, and can be used as a daily driver. High mileage use is not a problem with this engine. This is engine may also be setup for use in larger work trucks, or motor homes. We can also set any of our engines up for marine use.

This engine will produce nearly triple the horse power of the original bbc 396, 427 and 454's and much greater torque. Pump gas friendly. For those wanting to put this engine in a classic car or sport truck, select cam choice # 1 or # 2 with the Hurricane intake. This engine will deliver very impressive power in the lower rpm range, and have a very high degree of drivability and long life.

Two year warranty, see details below.

This engine uses a brand new World Merlin IV block, (standard deck height) with all new internals.

This engine is designed to have a very high level of drivability, or street manners.

Here are a few good reasons why we think the Stage 7.0 engine is a better choice than any of the original equipment big block engines produced by GM.

1. The Stage 7.0 bbc engine will accelerate any heavy car much better than any of the underpowered original GM bbc engines.

2. The exhaust note from this big block engine is much deeper than that of the typical stock GM big block engines.

3. Installing this engine in heavy cars or trucks without killing acceleration, or having to deepen the final gear, and needing a huge stall converter is a real plus. This engine will accelerate a 7500 lb vehicle much better than any stock bbc engine.

4. Low maintenance and high drivability even in very heavy cars and trucks, while generating up to 724 hp at the same cost as building a 496 engine.

5. Longevity and reliability. You don't have to turn the engine to a critical rpm range to produce its max hp output. There's nothing unsafe about running an engine that's well built like this up to 5,800 rpm. The hydraulic roller cam is very reliable and will not require a bronze distributor gear, as it has a normal cast gear. Our aluminum heads use very high quality hardware. All of our valves are from PBM, and are considered to be very high quality valves.

6. Should you ever decide to sell your car, or truck with this engine, the resale value would be much greater.

We do a full test run using an engine test mule on every engine we build. The engine is run for two intervals of 20 minutes each, and every possible issue is addressed. When you receive the engine, it will be ready to install and run. We also include an engine stand as pictured, wheels included, and an engine lift plate.

As of 10/25/2016, we completed installation of our second brand new Super Flow 902S dyno. This dyno is dedicated for dyno testing and tuning on our bbc engine line only.

De-tuned engines with different cam and intake combos will move the torque into the low rpm range, and is very desirable if you're sporting around on the street, rather than all-out racing. The de-tuned version of this engine will also allow you to set the car up closer to stock and increase drivability to a very high degree. Throttle response is also noticeably better. We can help you with a cam and intake selection that best suits your needs.

The compression range will be approx. 10.5:1 depending on how we set it up based on your needs. The Wiseco forged pistons are highly resistant to the damaging effects of detonation.

The build sheet is as follows:

 photo d3e145f8-9646-4aca-b54a-c205f4775329.jpg

BBC WORLD PRODUCTS MERLIN IV BLOCK BORE 9.800" STD DECK HEIGHT

 photo 8a630169-cbe1-4c9c-8f60-dd8591a7dafc.jpg

We now use all of the Merlin IV blocks in all of our BBC engine builds as of 7/17/2018. The Merlin block is light years ahead in overall construction as compared to any of the other blocks on the market. The main caps all have ARP hardware. Dimensional specs are spot on, and this has been an issue with other blocks we have used in the past. Many of the top engine builders, ourselves included, have found the new Merlin IV block to be superior to other blocks in numerous ways.

World Products has completely redesigned the famed Merlin Big Block Chevy casting, incorporating numerous improvements and new features to virtually every area of the block.

Designated the Merlin IV, this new block is offered in all popular sizes and deck heights and is sure to be a favorite among racers and professional engine builders.

New Merlin IV features include upgraded 35,000 psi iron alloy with added material in the main webs, cam tunnel, and cylinder walls for increased strength. Cylinder walls are nominally .300" thick on the thrust side at 4.600 bore. Material was then removed in non-affecting areas in order to maintain the original weight.

The block also has an increased volume priority main oiling system with a .500" main oil galley. A front oil feed for dry sump systems is incorporated with front oil cross-overs and restrictor provisions, which now utilize standard pipe plug restrictors. The main oil galley has been relocated so that blocks with a 60mm cam will not require bushed lifter bores.

This Merlin IV has a 55mm Babbitt cam journal and .904" lifters. Cam journals up to 2.480" or 60mm Babbitt and 1.062" lifter bores can be accommodated.

All deck heights are nominally .600" thick, feature blind head bolt holes, and use standard length bolts or studs. The inside head stud provisions have also been revised to add strength by extending the bosses below the deck thickness in the casting.

The new block features siamese cylinder bores in 4.595", which finish at 4.600". Nodular iron or billet steel 4-bolt main caps are standard and are stepped and dowelled register and utilize ARP fasteners.

The block is bored to size with our new Centroid touch probe machine. Few machine shops have a machine of this accuracy.

 photo CENTROID204.jpg

We also deck the blocks to an RA finish of approx. 15 or better. The decking procedure is also done by our Centroid CNC machine.

 photo CENTROID206.jpg

We often find many brand new blocks to have a sloping deck of up to 4 thous. When we're finished decking the block, it is within approx. .001 accuracy from end to end. Many machine shops fail to catch this as the machinery they use does not allow for such accuracy.

 photo 008202.jpg

We then plate hone the block with our new Sunnen SV10 diamond hone machine. This is also a very advanced machine that hones the block with a finish unlike conventional machines.

 photo Heads20049.jpg

The final step is to clean the block in our high pressure block washer.

Below are the specs of the rotating assembly portion of this engine.

 photo RA1.jpg

The picture above is a file photo of the rotating assembly that comes with this engine. See the detailed info below for the actual pictures and items included in this engine.

Fully balanced in house.

**********************************************************

Crankshaft Specs.

  • Crankshaft: Genuine Scat
  • Crankshaft Stroke: 4.250"
  • Crankshaft Material : Cast Nodular Steel
  • Journal Diameter: STD BBC
  • Rear Main Seal: 2pc RMS
Connecting Rod Specs.
  • Rods: Genuine Scat
  • Rod Type: Scat Pro-Competition, I-beam, Bronze Bushed.
  • Rod Length: 6.385"
  • Rod Material: Forged 4340 Alloy.
  • Rod Bolt/Cap Screw: ARP 8740 Cap Screws.
Piston & Ring Specs.
  • Pistons: Wiseco Fully Forged, with a fully machined crown. High Performance for street/strip use.
  • Piston Size: 4.500" when configured as a 540 cid or 4.560" as a 555 cid engine.
  • Dome Volume: Dome Top. Comp. Ratio will be right at 10.5:1
  • Compression Height: 1.655
  • Piston Material: Forged 2618 Aircraft Alloy
  • Piston Rings: Mahle High Performance, Moly, Standard Tension.
  • Ring Size: 1/16 1/16 3/16
  • Ring Material: Ductile/Stainless/Moly
Bearing, Damper, and Flexplate Specs.
  • Main Bearings: Clevite
  • Rod Bearings: Clevite
  • Balance: In House on CWT balancer.
  • Damper: Pro-Race brand SFI 7.0"
  • Flexplate: Heavy Duty SFI 168 tooth or 153 tooth. Manual Trans. flywheels available.

Listed below is a complete breakdown of all the parts that are included in this engine.

WISECO FULLY FORGED PISTONS, RATED AT 800+ HP. WISECO PISTONS ARE 100% MANUFACTURED IN THE USA. THEY ARE ONE OF THE HIGHEST RATED PISTON BUILDERS IN THE COUNTRY.

 photo WISECOBBCDOMEPISTONS.jpg

The Wiseco forged pistons are rated very high in the street/strip performance industry. They
are made using the 2618 aircraft alloy and have fully machined crowns. We prefer the 2618 alloy over the lower cost 4032 alloy. This alloy may fragment from the effects of detonation and if this happens, it can be very destructive to the engine.
Those types of pistons are fine for stock or mild engine builds, but should never be used in carbureted engines built to high horse power levels.
The forged 2618 alloy piston is much more resistant to the effects of detonation and heat.

Our Wiseco Forged pistons are custom designed with an increase in compression height. This has many advantages. Here are a few facts about compression height and deck height.

Our custom made pistons have a compression height that is .010 taller on bbc pistons, and .015 taller on sbc pistons, as compared to most all of the catalog pistons on the market. We find this to be a very valuable feature.

Since our pistons sit at a taller than normal compression height, we only have to remove approx. .005-.010 off the deck surface of the block. Our goal is set the piston at zero deck (flush with the deck surface). This maintains the deck's thickness, making it much stronger than a block that has been cut down .025. The engine will also run a bit cooler with a thicker deck. It's well known that the deck dissipates much of the built up heat an engine generates. This also allows for future deck re-surfacing without compromising the integrity of the block. On our bbc engines, we actually leave the piston about .003 to .005 in the hole to allow for possible piston rock. Our sbc engines will have the pistons setting right at zero with the deck.


You may have noticed that our Wiseco custom made forged pistons are referred to as Racing Pistons on the package. This does not mean that the pistons are for racing only. This is a generic term, referring to their ability to be used in high performance applications as well as for street rod use. These pistons are perfectly designed for use on the street, as well as for medium to upper level drag racing.

We have built approximately 5000 engines using the Wiseco pistons. The engines have been for street rod and strip use. We have seen no problems, nor have there been any complaints. They are an excellent product in every respect.


These pistons are also suitable for use with nitrous or blower setups.


The picture below is a file photo of our Wiseco pistons.


 photo BBCDOME1.jpg

MAHLE HIGH PERFORMANCE MOLY RINGS

 photo unnamed7.jpg

Scat Crankshaft.

The picture below is a generic file photo of a Scat crankshaft.

 photo SCATCRANKANDBEARINGS.jpg

Some of the benefits of the Scat crankshaft supplied with this assembly:

The material used in this crankshaft is manufactured from an exclusive Space Age material that was designed for high strength and fatigue resistance. The Scat cranks are the best value you will ever find. The Scat crankshafts are the best way to build a strong bottom end for, street rods, dirt and circle track racing, and drag strip racing. This crank is suitable for use up to approx. 600-650 hp.

Crank Polishing.

Pictured below is our ABS crank polishing machine in action. We polish the crank on every engine we build. This extends bearing life, keeps oil cooler, and with the reduced friction, a slight increase in horsepower is gained. Many machine shops fail to do this. The finish on most cranks are at the bare minimum of acceptance, and we know this can affect bearing life. We have measured the RA finish with our profilometer, and found it to be as high as 25 RA finish on many of the cranks. We bring that number down to below considerably.

 photo CRANK20POLISHER.jpg Photobucket

We now use the Clevite bearings in our engines.

 photo unnamed1.jpg

Our choice of rods are the SCAT COMPETITION SERIES rods with ARP-8740 cap screws.

 photo SCATCOMPETITIONRODS.jpg

 photo KGrHqQOKnUE64YDRDGrBOyDOflOeg60_12-1.jpg  photo KGrHqMOKjsE6QcBRNyBOyDOfP0860_12.jpg

The Scat Pro-Comp extreme duty I-beam rods should not be mistaken for ProComp rods. These rods are made exclusively by Scat, and have nothing to do with the ProComp company. The critical sizing and installation of the ARP cap screws is performed on a Sunnen machine in the USA by Scat Industries. These rods are excellent for those wanting the extra security offered by a rod with 7/16 ARP cap screws.

Take notice of the design of these rods. They are far superior to conventional style I-beam rods.

If you do a search on the Scat Pro-Comp rods, you will find a vast amount of info on many car forums. All of the info is 100% positive. These rods are run in engines that not only produce high horsepower levels, but also run at continuous RPM. Notice the general appearance in the pictures. These rods do look impressive. The style is reminiscent of a steel billet rod.

The fact that these rods are incredibly strong and well made, coupled with the fact they are light weight, made it an easy decision to use them in all of our high horsepower street/strip engines.

We have noticed some engine builders using low cost generic rods and crankshafts in their engines. These non-branded, (no-name) products are often poor quality in many ways. You will notice many of the low end engine builders fail to mention the actual brand of the rods or cranks used in their engines. Upon further investigation you will find such parts not to be a branded name product. They may label these parts with a name, but one that is totally unrecognizable in the industry. Our experience in years past with such rods and cranks has been disappointing to say the least. Besides the obvious issues such as incorrect sizing and machining that is difficult to correct, the questionable alloy these items may be produced from and the potentially incorrect heat treating methods used, could prove to be disastrous. Little can be done to verify this and nothing can be done to correct it. Failures of such critical parts will usually result in catastrophic damage to the engine. As you may have noticed, this is why we specify the brand name, and series of every part used in our engines.

Many of the inferior "no-name" rods on the market will also have "no-name" rod bolts in them. We have seen these bolts before, and they are very low quality. They don't have ARP's rolled thread design, and they don't torque down with the same characteristics as a genuine ARP bolt. It's not just a matter of having a different brand bolt in the rods; these bolts are low quality in many ways. They have been known to fail in engines to a much greater degree than a high quality rod bolt, and this failure usually causes catastrophic damage in the engine. Beware of rods that don't mention the rod bolt brand. As far as we're concerned, ARP bolts are the only brand we would ever use or accept in a set of rods.

Genuine ARP 8740 cap screws.

 photo arp-2566301_3530201.jpg

PRO RACE BRAND SFI HARMONIC DAMPER, 7.0 DIAMETER INCLUDED.

 photo dd1c4df4-600b-415d-a8fa-4da36cf951c3.jpg

Pro-Race brand dampers are used on all of our engines.

We have noticed others using a low grade knockoff brand damper/balancer, and we have encountered them in the past. They are substandard in appearance, and are often out of spec. The timing marks were also poorly marked on some of the balancers we have come across. Another problem with low grade dampers is the elastomer bonding can lose its adherence to the inner and outer structure. This problem is referred to as a slipped damper. We have only encountered this once in 10 years with the Pro-Race brand dampers.

BILLET ALUMINUM TIMING POINTER. VERY FEW SELLERS FINISH OFF THEIR TURN KEY ENGINES AS WE DO.

We did not offer this billet timing pointer in the past. However, we noticed that there was a birds-eye view of the timing pointer from the driver side of the engine, so we decided to use these on all of our engines.

 photo ed57b319-46ba-4f28-8ff8-dbda7a71201f.jpg

 photo RESIZED.jpg

HEAVY DUTY SFI RATED FLEXPLATE MADE IN THE USA INCLUDED.

 photo BMM-20230_xl.jpg

This SFI flexplate is made in the USA and will resist cracking and warpage to a very high degree. One good telltale in identifying a low quality flexplate is the lack of welding on each side where the plate mates to the ring gear. They usually have a pale grey color to them, as they are not coated, and will rust quickly. Ours are welded on both sides, and are much thicker than an OE plate, and are zinc dichromate coated.

We do offer this engine with a manual flywheel. In most cases we do have both sizes, 153 and 168 tooth, available.

Our CWT 5500 Balancer.

We do our own balancing with our new state of the art CWT 5500 Series balancers. The CWT 5500 is the ultimate for precision balancing. We now have three of these in our machine shop. We consider this machine to be highly advanced compared to the Hines balancer we once used. We balance every rotating assembly we sell within 2 grams or less at no extra charge. A balance sheet is included with your assembly.

 photo 0f868548-473a-4934-a4fe-c743585a9ed1.png

 photo 20151218_111921.jpg

Three CWT balance machines under one roof is a rare sight.

 photo IMG_0589.jpg

Our crew wrapping up for the day. Pardon the mess.

Bravo aluminum cylinder heads. 335cc runner size.

 photo 9b66dc80-424f-4589-b35b-f2d7959bb4a4.jpg

Assembled by us with premium PBM competition grade valves, Melling springs, Comp retainers, Comp Viton valve seals, Comp spring ID locators, Comp 10 degree locks.

Notice the multi angle valve seat cut. These heads are designed to very high standards.

 photo 48d8afb2-9bf4-4e02-bad9-4551b730019d.jpg

Below are the actual flow numbers for the Bravo heads. These numbers are true and accurate. The testing methods we use are considered to be on the conservative side. Some choose to show flow charts for their heads that have been done in a way that shows numbers that are misleading in our opinion. We use the Bravo heads on most all of our bbc engines builds all the way up to the 572 engine. The horse power numbers they produce are exceptional as compared to any of the low to mid range priced heads on the market.

Intake Flow

Exhaust Flow

.100
.200
.300
.400
.500
.600
.700

73
145
215
285
320
345
360

.100
.200
.300
.400
.500
.600
.700

71
120
165
200
228
249
266

Fel Pro 1057 premium race grade series head gaskets, ARP head bolts, and rocker studs.

 photo 3da2777c-172a-4176-99aa-ac90f302e173.jpg

ARP HEAD BOLTS AND WASHERS AND ROCKER STUDS.

 photo arp-134-3601.jpg

 photo arp_100-7101.jpg

SCORPION RACING ALUMINUM ROLLER ROCKERS or COMP ULTRA PRO-MAGNUM ROCKERS.

 photo dsc05169ebay.jpg  photo 8bfd8b34-f95f-42f7-a7bc-299622d208ec.jpg

THE BEST HIGH PERFORMANCE RACING ROCKER ARMS MANUFACTURED IN THE USA.

Our bbc 572 and 598 engines use the Scorpion Endurance Series rockers, which are the top of the line. We use them instead of the regular Race Series Scorpion rockers because they weigh 496 grams less per set. This is a monumental difference when it comes to valve train weight. They cost considerably more than the regular race series Scorpion rockers, but the increased performance and reduced burden on the valve train is well worth it. You may choose the Comp Ultra Pro-Magnum rockers instead of the Scorpion rockers at no additional cost. They are both very high quality roller rockers.

We were amazed at the low level of sound produced in the valve train when we did a test run using our first set of Scorpions. We attribute this quiet operation to the close tolerances in the trunnion section. The trunnion barrels are also micro polished.

The rockers have a lifetime warranty. The aluminum body is made from a 7000 series aircraft alloy. Most rockers have a considerable amount of side play in the trunnion section, and may have an excessive amount of needle bearing clearance. The Scorpion does not have much of a loose feel in the trunnion. Many round track and drag racers run these at very high rpm levels and even run them on solid roller setups. With the milder spring pressures of our engines, these rockers should last a lifetime.

The potential for valve float under high rpm is a real issue with most high performance engines using hydraulic roller components. By reducing the weight on valve train components, you also considerably reduce the possibility of valve float as well as wear and tear on the valve train components.

The significant reduction in weight of valve train components will dramatically increase the life of every moving part in the valve train. Since some of our cam choice options are large, and these engines may be driven many miles, we see this reduction in weight as absolutely necessary. The lighter weight components do not reduce the durability of these items; on the contrary, they improve durability significantly. These components are high quality, so the weight reduction in their construction does not compromise them in the least.

All Scorpion Rockers Feature:

Needle Bearing Fulcrum and Roller Tip, Centerless Ground Trunnion, Centerless Ground Pin & Roller, Burr-Free Thru Hole in Trunnion, Large Machined Seat, Thick Walled Adjusting Nut, Pedestals Machined from Solid Steel, Black Oxide Coated Steel Parts, & 100% CNC Machined.

Important notice.

If you've read our warning on engine builders using low grade no-name rods and cranks, a similar situation exists in the roller rocker market. We do not use or sell off-shore, (no-name) roller rockers, period. They have proven to be faulty in many ways. The center trunnions are not polished, nor is the center of the roller tip true to size or polished. Metal fragments are often left inside the trunnion housing and will cause destruction of the needle bearings. The aluminum alloys used are never aircraft aluminum alloys as are used in all USA made roller rockers. They often mention the alloy as being 6061, and that is a very soft form of aluminum. The 6061 alloy used on these will assure rocker-flex on any higher than stock spring pressures, and this will affect performance. The pins and keepers that hold the parts together are often of poor quality and improperly installed. The front roller will usually scoot along the valve tip, as it can't roll properly due to rough internal surfaces.

We have honestly seen valve tips that were scalloped out due to the front roller dragging across them. This will cause the valves to side-load against the valve guides in the heads and surely cause damage to them if run like this for very long.

We have scrutinized these products in the past and found all of the above problems, and I can tell you there are most likely many more. We would not use them in an engine under any circumstances. You will also see many of these rockers made from stainless on the market. They use a low grade stainless that actually has a near non-existent amount of nickel in them, but that's not the real problem with them, as stainless steel has no advantage over high grade heat treated steel when it comes to a roller rocker. The lack of hardness of the rocker body is the real problem. The problems with these stainless rockers are the same as mentioned above. These are the roller rockers you see on the market for around $119 and up to $169 for the so called stainless ones. They are pure junk, in our honest opinion. They could possibly be used on a budget back yard stock build up that has a very low spring pressure, with a cam that has very low lift, but then you would be better off with the stock stamped rockers on such a build.

We have heard of many engines using these rockers that came apart and spilled needle bearings into the engine, only to end up in the oil pump. It seems like some engine builders do not care how long the parts in your engine last, or they simply don't know this. I can tell you for sure that using such low grade, "no-name" roller rockers is asking for trouble.

We use Scorpion, Comp Ultra Pro Magnum, and Comp Gold Arc rockers in all of our engines. The difference in these compared to the low grade no-name rockers on the market is huge.

HOWARDS LIFTERS & HOWARDS CHROMOLY PUSHRODS.

 photo ce444187-39f3-4bd0-a501-3023a1ebd097.jpg

Photobucket

We use Howards brand premium pushrods in all of our engines. They are lightweight in design, yet very strong. Made in the USA from 4130 chromoly steel. Regular hardened pushrods will most likely flex in the engine when running above normal RPM ranges, and risk bending under high RPM. These do not have the welded ball on the end. We only use the swedged one pc. design, which is a well proven design far superior to the style many others use in engines. 4130 chromoly steel is also much stronger, and will resist flexing. When a pushrod flexes in the engine, you lose lift. Don't be misled by the term "hardened," as this is nothing more than a stock style low cost push rod. They will flex in the engine or possibly bend permanently.

Our choice of lifters are the Howards brand tie bar lifters. These lifters have many unique features.

Pictured below is our Speedmaster single plane intake. We also offer the Edelbrock RPM Air Gap intake as an alternate choice.

 photo pce147.1027_1.jpg

 photo 5ffd5fbc-5a5c-4e6f-974f-125c7c6bb754.jpg

304 STAINLESS ALLEN HEAD INTAKE BOLTS ARE USED ON ALL OUR ENGINES.

 photo SBCSTAINLESSINTAKEBOLTS125.jpg

We are offering three cam choices listed below in this engine. Read the specs carefully.


 photo a85621cb-be4e-47c9-aa40-e03a9ab47683.jpg

Cam Choice # 1 By Comp Cams.

Part number: 01-461-8

575/575 lift.

254/260 duration

112 lobe sep.

Cam choice # 1 offers decent drivability and low end power. Valve train stability and longevity is very good with this cam. This cam is recommended for use in light to medium weight vehicles with tall gearing, and sport trucks. Max power will be achieved at approx. 5900 rpm. You may use the single plane intake with this cam and not affect the low end power to any noticeable amount.

We recommend a stall converter in the 2250-2500 rpm range. Final gearing when used in a car or sport truck could actually be in the 3.55 range or even taller, and overdrive use may be possible. Mileage with taller gearing is also a plus. This cam would be suitable in heavy vehicles weighing up to 4500 lbs. Drivability with this cam is decent. This cam may not develop enough vacuum to operate power brakes.

Official Dyno Results on Cam Choice 1 in our 555 engine with a single plane intake and our new 335cc rectangular port heads.

555-compcam-575-575-rec-sp 2 photo b28a89b3-e8f9-43e8-bf32-5934f68ec6b9.jpg

This is an excellent cam and head combination. Our new 335cc bbc heads have proven to be exceptional.

555-compcam-575-575-rec-sp 2 graph photo 9dac2b16-2f63-4fe7-8c1b-85284520f700.jpg

Official Dyno Results on Cam Choice # 1 in our 555 engine with a dual plane intake and flat top pistons. This engine had the low compression, (9.56:1) flat top pistons, and our former line of cyl. heads. Our new heads would have possibly exceeded these numbers especially with normal compression ratio. This setup would have been better suited with the Cam choice # 2 from what we're seeing. Low compression setups are for very heavy vehicles, and smaller cams are more in line with such setups. The smaller cam would have made better off idle power.

 photo acebce88-e32c-49cc-9815-ce17ea8ee589.jpg

 photo 03f9a45d-075d-4fee-88f8-b349c2af7d05.jpg

Cam Choice # 2 By Comp Cams.

Part number: 01-456-8

566/566 lift.

242/248 duration

112 lobe sep.

Cam choice # 2 offers a decent amount of bottom end torque compared to cam choice # 1. This cam selection is the best choice for cars that have very medium to tall gearing. This cam will allow the engine to operate well in the 1900-2000 rpm range. Very good acceleration with improved street manners. The peak horse power falls about 15-20 under cam choice # 1. This cam would also be excellent for medium to heavy vehicles. Max power is achieved at approx. 5700 or less. This cam has been very popular for those more concerned about drivability and outright longevity of the valve train and engine engine. The valve train wear with this cam would be very low. Off idle power is decent. We see no drawbacks to going with this cam. The power in the low rpm range is amazing. Vacuum should be enough for operating power brakes.

Official Dyno report with this cam choice, Bravo heads, a single plane intake, and an MSD distributor.

555 566/566 dyno photo 89c548d2-8923-4722-90a6-ece01053991a.jpg

555 566/566 graph photo e05df7b1-ab3f-44b6-bddd-c7ebc96494e8.jpg

Cam Choice # 3 By Comp Cams.

Part number: 01-451-8

547/547 lift.

230/236duration

112 lobe sep.

Cam choice # 3 offers a huge amount of bottom end torque. This cam selection is the best choice for cars that have very tall gearing or overdrive transmissions. This cam will allow the engine to operate well in the 1800 rpm range. Very good acceleration with excellent street manners. The peak horse power falls an additional amount of about 15-20 under cam choice # 2. This cam would also be excellent for heavy vehicles, quad cab 4x4 pickups. Max power is achieved at approx. 5500 or less. This cam has been very popular for those more concerned about drivability and outright longevity of the valve train and engine engine. The valve train wear with this cam would be virtually non-existent. Off idle power is very good. We see no drawbacks to going with this cam. The power in the low rpm range is amazing. Vacuum should be enough for operating power brakes. Long range cruising and operating air conditioning is not an issue with this cam.

We have several different options in valve covers. Here are our most popular choices:

 photo unnamed.jpg

These are just a few of our popular valve covers you may choose from. We do have several more choices to select from in our other listings at no additional cost.

 photo 9cb8609b-9a85-496f-a838-14c7eb89224e.jpg

Billet Aluminum Breather set.

 photo 6ffc9dc0-2bae-4209-9deb-54aaebcc46ad.jpg Photobucket

If you chose cam choice 1 or 2, then we highly recommend using an exhaust evac. system. The vacuum created by the engine is somewhat insufficient when using these larger cams, heads, carb and intake to operate a pcv system at its best. The exhaust evac system will pull the crankcase gases out of the engine at a very smooth and controlled rate. This allows the rings to seat in much faster and better, and can increase horse power to some degree by reducing crankcase pressure. Another benefit of the evac system is that you're not contaminating the fuel and air mixture with semi-burned byproducts from the engine oil and combustion process.

After the engine is completely broken in, the pcv setup may be sufficient. However, it may not be the best choice. The break-in time may also be slower with the pcv setup.

We also offer a vacuum pump system for the ultimate in crankcase pressure control.

If you do decide to use an exhaust evac system, we have a few more recommendations. The bullet style perforated mufflers, like those made by Magnaflow and many other companies, must be used. In our opinion, they sound the best and, most importantly, they allow the exhaust evac system to work properly. Magnaflow is a popular brand of the true straight through mufflers, and there are several other brands on the market such as Corsa, Borla, and Bullet. The sound level is controlled by the length you choose. The 12-16 inch length sounds the best to us. These mufflers have smooth perforated inner walls. They should not be confused with traditional glass packs with fluted walls, which are very restrictive and have a somewhat sloppy sound.

Traditional chambered mufflers, like Flowmaster, create a back pressure pulse that will interfere with the operation of an exhaust evac. system. Chambered mufflers have the reputation of helping bottom end throttle response, but you will have a decent amount of bottom end power with this engine, especially if you have chosen cam choice 2, 3 or 4. In our experience, the straight through perforated mufflers sound and perform better in every respect, and allow the proper use of an exhaust evac. system. More info. on this subject below.

Timing components: SA Gear 8999T billet double roller timing set.

Polished Aluminum Timing Cover.

resized timing cover 2 photo 10eae791-af95-4125-b534-76c3c7a69f73.jpg  photo b8d65904-41f4-4620-ae13-76480c987d33.jpg

We use the top of the line SA Gear timing set with a torrington bearing and rolon chain. The difference in quality is dramatic compared to the common low-cost timing set. The upper sprocket is made from billet steel and the lower is induction hardened with nine keyways. These sets are hand matched for selective sizing.

The cost on this high end timing set is approx $97.50, more than double the cost of the low level budget timing set used by many other engine builders. Should you ever want to confirm that this is what is actually in your engine, you can remove the timing cover, and you will see that this timing set is very different in appearance to the run of the mill low cost sets often used by others.

This timing set is offered in three different chain tension setups, allowing us to set it up perfectly every time. One more benefit is that timing accuracy is very precise and will remain that way. This timing set will likely last for the life of the engine. This is what you will find in most solid roller engines, as they have very high spring rates, and create an enormous load on the chain and gears, compared to non solid roller setups. It may seem like a bit of overkill to use such a high end timing set, but the versatility and extreme quality outweigh the cost, in our opinion.

Champ premium oil pan.

The oil pans we use on all of our engines are made in the USA by Champ. The Champ oil pan has a full windage tray, crank scraper, and trap door. Threaded dipstick is included. Extreme duty pickup designed not to fail. The oil pan is made from a thicker than normal gauge material, and has embossed ribs in the body.

The 7.5 qt Champ oil pan has kickouts that swell outward approx. 3 inches on each side. If you think you will encounter clearance issues with the kickouts, we recommend opting for the stock appearing 6 qt. oil pan. The 6 qt. pan will still be a Champ pan and will have the windage tray and crank scraper. We strongly recommend reducing the amount of oil used in these oil pans by approx. 1/4th to 1/2 a quart. Doing this may greatly reduce the chance of oil leaks, and reduce oil temps. The larger counter weights used on stroker crankshafts are why we recommend reducing the oil capacity in these engines.

To be clear on what we're saying, we would like to see you add right at 7.0 to 7.25 quarts of oil grand total in your engine and oil filter when using the higher capacity oil pan. When using the stock appearing oil pan, we would like to see you add right at 5.5 to 5.75 quarts grand total in your engine and oil filter.

Our engines include a dipstick. It's very important that you re-calibrate the oil level marking on the dipstick. This is due to the fact that the dipstick, oil pan, and block are all made from various manufacturers and we often see great variances. Couple this with the fact that you may be running a reduced amount of oil, and the "full" mark on the dipstick will most likely not indicate correctly. Once you have put a predetermined amount of oil in your engine, and run it for a few minutes, let it sit for awhile on level ground, check the oil, and mark your dipstick with a flat file to re-establish the full mark.

 photo SBC8QT4.jpg

 photo 003.jpg

 photo 006.jpg

 photo 004.jpg

 photo 012.jpg

 photo 0041.jpg  photo 0035.jpg

The quality of these pans far exceed any of the lower priced oil pans used on many engines.

We do not use the knock off oil pan gaskets on the market. Felpro premium oil pan gaskets are used on all of our engines.

Pictured below is a file photo. The actual Felpro gasket used will be the correct model for this application.

 photo 9e944296-9171-44d8-a95c-d2250713950a.jpg

Studded Mini Nut Set.

Photobucket

 photo 13752979-cd6a-4967-bac4-ca1009585ea9.jpg

We use our premium studded mini nut set on all of our oil pans and valve covers. The nuts have a serrated face and built in washers. This is the ultimate set for securing the oil pan and valve covers to the engine and is far superior to the typical bolts used by most other engine builders. Our standard engine color is black. Custom paint work on engine blocks and oil pans is available as an optional upgrade. The pictures above and below are file photos to display the studded mini nuts. Other items seen in these pictures may not represent your actual engine.

 photo 08768697-789b-490a-a7aa-3eb558bcea2b.jpg

Melling M-Select Oil Pump, and M-Select Drive rod with ARP stud.

 photo ead7d257-d0df-41cb-82e2-93aade88ccfb_1.jpg  photo 04d4687f-eac3-4d6d-b98e-db1ef0a5c092.jpg

The M-Select series oil pump by Melling has several important upgrades compared to the regular Melling M-55 Series. The gears are billet steel, and the body is stronger, coated with corrosion-resistant nitrite. This oil pump also includes the M-Select drive rod. Both components are far superior to the regular Melling oil pump and drive rods used by most other engine builders.

Pictured below are the front end accessories that are included with this engine. They will be installed on the engine.

This is our satin high volume long style water pump with aluminum impeller. This is a very high quality pump.

 photo 6cf89ed4-73b5-490b-bf3b-fbc2bde9c50e.jpg

Our 120 amp chrome plated one or three wire alternator.

 photo 38e5_1_sbl.jpg  photo 30a6_1_sbl.jpg

Chrome plated power steering pump.

 photo RESIZED PS PUMP.jpg

We are confident that the price we have on our engine will never be matched by our competition!

We include an engine lift plate and heavy duty engine stand with casters with every engine we build.

 photo 2c9df2a4-d6bd-4585-8939-27682d3069f7.jpg  photo 4bc7b02e-155f-4718-94f7-8a31cb63bb5f.jpg

We offer this engine with selected upgrades and options. Listed below are some of the most requested ones. Many not only improve performance, but further enhance the reliability and longevity of your engine, along with resale value.

Flywheel upgrade/option for manual transmission builds. Upgrade to a 168-tooth or 153-tooth flexplate for manual transmissions.

Cost for this option is $105.00 We have this upgrade/option featured in our other listings. There will be a 153 tooth and a 168 tooth size available. Be sure you know the size you need. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this engine, you may add any of these upgrades to your shopping cart. Click here to add upgrades.

6504 front resized photo 62d2edce-c79a-4437-b2be-dd70d1b90808.jpg

SFI Billet Steel flywheel upgrade/option for manual transmission. Upgrade to a PRW brand billet steel flywheel SFI rated 168-tooth or 153-tooth flexplate for manual transmissions. We highly recommend the SFI billet steel flywheel for those running hard. These are fully cnc'd and far superior in many ways compared to the regular cast iron flywheel.

Cost for the SFI billet flywheel option is $169.00 We have this upgrade/option featured in our other listings. There will be a Chevy 153 tooth and a Chevy 168 tooth size available. Be sure you know the size you need. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.

 photo 2b51463a-12d1-41c4-91aa-668dce226a17.jpg

BBC Scat H-Beam Rod upgrade from Competition Rods: Recommended for those running hard. The Scat Competition rods that come with this assembly are sufficient for most street rod uses, but the Scat H-beam rods will most likely offer more security against rod breakage under hard use. The H-beam rods have a 750+ HP rating.

Cost of this upgrade is $90.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this engine, you may add any of these upgrades to your shopping cart. Click here to add upgrades.

Photobucket

ARP-2000 rod bolts: This is one upgrade that we find to be very valuable. The rod bolts are most likely to fail under hard use, moreso than the rod itself. When a rod bolt fails during high RPM, total engine destruction is usually the result. The ARP-2000 rod bolts are a very good upgrade, in our opinion. We actually have few, if any, problems with the regular ARP-8740 bolts, but those who run hard always upgrade to the ARP-2000 rod bolts. The ARP-2000 rod bolts also torque at a higher number, and this increased clamping force is also a factor in keeping the big end of the rod stable and true to size. The ARP-2000 bolts are installed in the rods and this upgrade is only available with the Competition rod upgrade.

Cost of this upgrade is $85.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this engine, you may add any of these upgrades to your shopping cart. Click here to add upgrades.

 photo arp-2566301_3530201.jpg

BBC Scat 4340 Forged Crank: The forged Scat crank has a rating of 800+ HP. This is the ultimate upgrade for those wanting to run hard. Nos, blowers, turbos, are not an issue with this crank. Even without such power adders, this Crank offers great protection under the most severe conditions. This upgrade also comes with the HP high Performance King bearings. Should you decide to run power adders in the future, this would be essential. The fatigue life of the 4340 crank over the cast nodular is also greatly extended. We do offer this upgrade as part of many of our assemblies in some of our other listings. They have the key words, "fully forged," in the title.

Cost of this forged crank upgrade is $380.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.

 photo chevy_big_b_cc.jpg

Polished Speedmaster intake upgrade:The polished intake upgrade is very popular, and certainly adds a bright fresh look to your engine.

Cost for the polished intake upgrade is $61.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this engine, you may add any of these upgrades to your shopping cart. Click here to add upgrades.

 photo 20d5ae58-1af3-4d3f-af85-a9869ae1d68e.jpg

Dyno Tuning: This is one of the most important upgrade/options we offer. There are many benefits to this service. The engine is first run at fast idle to bring the water and oil temp up to normal operating temperature. It is then run for approx. 20 minutes under a simulated load at around 3k rpm to promote initial ring seating. After this, the engine is shut down to allow us to check the readings on the spark plugs, and for any possible oil leaks. This cool down is considered part of the engine's first heat cycle. We then follow up with multiple low to medium rpm runs to further the break-in process of all the moving parts in the engine. During these multiple runs, we are paying close attention to the EGT, (exhaust gas temp) readings, vacuum pump readings, oil temp and pressure, coolant temp, and overall engine sound. At this point, we start the actual dyno tuning process and this focuses around the air to fuel ratio numbers and what timing numbers produce peak power. We usually have to change carb. jetting several times, adjust the idle circuits, and the air-bleeds occasionally have to be changed. We then establish the engine's full horse power and torque numbers at a given rpm limit.

Having your engine dyno tuned will allow it to run its absolute best, and is very important in protecting the engine from potential damage caused by the carburetor running excessively rich or lean. This also establishes the engine's hp output and max rpm. These numbers are very important to know. There is one more value we consider just as important to what we have mentioned above. An engine that has been dyno tuned has also been validated to be in perfect operating condition. This is something that running the engine on a test mule can't provide. Any problems the engine may have will show up during the dyno tuning process. We have on rare occasion seen a popular combination show hp numbers that were not where they should be. Some of these problems give no indication other than reduced hp numbers. We find and fix such problems. The problem may be something simple and easy to find and in some cases very difficult to pinpoint. We will not send the engine out until it's perfect. If you choose not to purchase the dyno tuning package, we will still do a test mule run, as many engine builders do, and it certainly is better than nothing but pales in comparison to a full dyno tuning. When engines are dyno tuned, the chances of you having a problem are near non-existent. Unforeseen problems may still, occur but they are rare. We have kept the cost on this extensive procedure low to not only make it affordable, but it gives us great peace of mind knowing the engine will be in perfect operating condition when it is received. The cost to do a repair once the engine is installed can be very expensive for both us the seller and the customer. When you see the final dyno run of your engine on youtube, consider the fact that approximately five man hours, around $25.00 worth of fuel, oil and filter and $105K worth of dyno equipment went into making that one minute final test run video.

Cost of the full dyno tune option is $350.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this engine, you may add any of these upgrades to your shopping cart. Click here to add upgrades.

Pictured below is one of our actual Super Flow dyno's. This is a 2016 model and highly advanced compared to the much older models many shops have. We have two of these in use at our shop.

 photo fbabd93c-49ce-45cf-9aa8-a63dad310994.jpg

The Super Flow is the best dyno in the industry.

 photo 8df98e36-edf7-4e3c-8644-9617dcd857e8.jpg

WARRANTY INFORMATION

This engine has a Two Year Warranty with unlimited mileage.

  • Should a major problem arise with this engine within the first year of use, the warranty covers all parts and labor and we will pay for shipping the engine both ways.
  • Keep the crate your engine came in to ensure a safe return to our workshop.
  • We do not cover the removal or re-installation of the engine at any time during the warranty period.
  • Our engines must be used with a rev limiter. Should warranty issues arise, proof of the rev limiter use will be required.
  • Should a problem occur in the first year of the warranty that we determine can be repaired by you or a qualified repair shop, upon our written approval, we will pay for the repair based on our in-house hourly rates for labor and our estimate of a reasonable amount of time to make the repair with the engine on a stand as you received it. To be specific, due to the difficulty of accessing certain engine parts in some vehicles, we are not responsible for the additional time and labor costs you may incur in removing and replacing such parts.
  • In the second year, the warranty will cover all parts minus any labor to remove and install needed parts. The cost of shipping the engine to us is not covered in the second year of warranty.
  • Tuning or maintenance are not covered under the warranty. Tuning includes jetting or adjusting the carb, ignition timing, or readjusting the rockers. Tuning would also include changing out plugs to optimize temp range for your needs. Setting ignition timing is also considered tuning. You must check the timing on this engine before it is driven.
  • If you are not satisfied with the cam or intake you have chosen, we will exchange any of these items for up to 60 days. You will pay for shipping and any required labor.
  • Damage due to overheating, detonation or extreme abuse will not be covered by the warranty. Detonation damage is evident upon removal of the cyl. heads.
  • Engines used in marine applications will have a limited warranty of 1 year. The first six months will cover parts and labor, and the second half of the one year period will cover parts only. Marine engines must upgrade to a 4340 crank unless the engine already comes with this, and the ARP-2000 rod bolts.
  • All external items on the engine, such as the carburetor, distributor, alternator, water pump, and power steering pump, will be warranted for the time period specified by the manufacturer. Most of these items have a warranty of one year or less.

You can enjoy your engine with occasional spirited driving, as it is well designed for it, but we will not cover damage caused by racing or improper tuning. A rev limiter and fuel to air ratio monitoring device must be used on this engine. The rev limiter should be set to cut off at its peak horsepower or less if you choose, and this should allow many years of service without a problem.

Your carb should be tuned to allow the correct fuel to air ratio. This ratio can vary depending on many factors such as altitude, vehicle weight, gearing, type of driving, etc. These values should be in the recommended safe zone.

Pre-Installation/Pre-Run Recommendations.

  • It is highly recommended that you re-torque the intake manifold. The gasket sealant tends to shrink after a period of time and this may cause the intake bolts to lose their proper torque values. The torque range is approx. 25-30 lbs.
  • The spark plug gaps should all be re-checked. For those running an HEI distributor, the plug gap should be approx. .040-.045 Those running an MSD 6AL unit should gap the plugs to approx. .035-.040 These values are very controversial and you may experiment as to what runs best in your engine. Widening the gap too much can put a strain on the ignition components. Be sure your plug wires are completely fastened onto the spark plugs.
  • If your engine came equipped with a front end accessory setup, we recommend that you check all of the bracket and pulley bolts. It would be rare to find any of them loose, and it should only take a few minutes to check. We would also like you check the belt alignment.
  • Check your flexplate or flywheel bolts.
  • Check fuel bowl levels in the sight glass on the carb once you have the engine running. Be sure your fuel pressure is set in the correct range. Adjust the choke on the carb. We would prefer you set the choke to a loose setting. Setting it tightly may allow it do its job better, but can cause engine damage over a period of time due to excess fuel entering the engine upon warm up. Be sure to use a high quality fuel filter.

You may not find a problem with any of the items mentioned above, but considering the small amount of time it takes to check them, we find it to be a valuable preventive measure.

As it's been said, "an ounce of prevention is worth a pound of cure."

Continue reading for more detailed information on timing and carburetion. You must follow the recommendations listed below.

Tuning, maintenance, and oil recommendations.

This engine must be maintained with oil specifically designed for high performance engines. The life of the engine can be greatly extended if you run a race grade engine oil such as our Schaeffer brand racing oil. We strongly recommend the Schaeffer Micron Moly 20w-50 grade in warm to hot weather or you may run the 10w-30 weight Schaeffer Supreme 7000 series semi synthetic oil in cooler weather. The part number for this oil is 709-06 for the six qt. case or 709-12 for the full case. After the engine is fully broken in, you may move over the Schaeffer full synthetic oil. The Schaeffer brand oil is very highly rated. It is the only brand of oil we use when dyno tuning. Racing oil must be changed more often than conventional oil. Every 2000 miles or less would be optimal.

We offer a full line of this oil in our other listings.

Oil pressure of 50-60 lbs in the upper rpm range on a fully warmed up engine is nothing to worry about. You may also notice that oil pressure drops at idle to approx 25-30 lbs when the engine is fully warmed up during very hot weather. This is somewhat common and no cause for alarm.

If your engine has a Merlin IV block, then it has priority main oiling. This block routes the oil in a very different pathway compared to a GM block. The mains and rod bearings as well as the crankshaft are well protected with an ample supply of oil even when the oil pressure numbers are lower than you think they should be.

There are many special additives in race grade oils that are not in conventional oil. These additives are very valuable for high performance engines. Never add anything to racing oil. This oil has exactly what is needed to protect a high performance engine. Some of these oils will state that they are low or possibly non-detergent, and that is a desirable trait of racing oil.

The anti-foaming agents in race grade oils are much better than what you would find in conventional motor oil. Race grade oils have higher than normal amounts of the zinc compounds in them, and there are many components in the engine that can make great use of these additives.

This engine does not include a fuel pump. This engine is best suited to operate with an electric fuel pump, with a pressure regulator set at 6-6.5 psi. A chrome block off plate will be installed on the engine. We believe that the electric fuel pump system is a superior fuel delivery system compared to a mechanical system. If you decide to run a high volume mechanical fuel pump on this engine, then you must use the special polymer fuel pump rod, and you must also use a fuel pressure regulator, and gauge, set to approx. 6.0-6.5 psi. Only use engine oils with zinc compounds in them when running a mechanical fuel pump. This will protect the eccentric fuel pump lobe on the camshaft. We strongly recommend the Schaeffer Racing oil. See our other listings for this oil.

If you insist on running a mechanical fuel pump, then using a race grade oil becomes essential. To further protect the cam, we offer a very special fuel pump rod made from an ultralight material. It’s made from a proprietary blended, carbon reinforced, bearing-grade polymer. This fuel pump rod only weighs 25 grams, and is very strong yet gentle on the eccentric cam lobe.

Unlike the common light weight hollow rod on the market, this rod is one third the weight, and a bit more costly. By reducing the reciprocating mass of the fuel pump rod, the load on the eccentric cam lobe is greatly reduced. We offer this rod in our other listings.

As for oil filters, we recommend a high quality oil filter. Racing oil filters are excellent.

You must use a rev-limiter on this engine. Should you have a warranty issue, proof will be required. A rev-limiter will allow you the freedom to drive without having to monitor the tach. Every car from the factory has this feature. Set the limiter to the peak hp rating of this engine or less for added protection.

We recommend using a crankcase ventilation system to pull gases from the crankcase. The exhaust evac system we recommend is made by Moroso. The benefits are numerous as compared to the typical pcv system. Oil leaks are greatly reduced by using the exhaust evac system.

Engine break in: As soon as your engine is installed, check and reset the timing if needed.

Drive safely please but keep your engine under load more than normal and bring the rpm up and back down to seat the rings much better and faster. This allows the rings to expand in a perfect circle and with greater pressure against the cylinder walls to establish an even wear pattern. This is why race engines are dynoed: to put a good number of passes on the engine under heavy load, as this will partially seat the rings very quickly, making the engine somewhat ready for racing. Failing to do this not only delays the break-in, but can permanently stop the engine from establishing a good wear pattern on the cylinder walls.

If you have opted for our dyno-tuned version of this engine, then ring seating will be partially established. The dyno has a computer controlled break-in mode that we use before doing any dyno testing for power output. Should you opt for the dyno tuning package, it does not mean that your engine is ready for full synthetic racing oil. Your engine will continue to seat the rings in to an even higher degree after 300-500 miles of driving.

VERY IMPORTANT NOTICE.

This engine does not come with oil in it. The oil that was used during the test run or dyno tuning will be drained as this is required by the shipping companies. We also prefer draining the oil as this gives us a chance to examine it for metal particles. The filter is removed and is also closely examined for metal particles or debris. To prevent oil from dripping onto the shipping pallet, we re-install a new low cost regular spin-on oil filter.

You should replace the low cost oil filter that comes on the engine with a high quality oil filter, but opt for the medium length version, as this will help maintain oil pressure and volume much better than the short version.

You must prime your oil filter. Priming is not needed when changing oil on a well broken-in warm engine that has been running moments before changing the oil. If your new engine has been sitting around for weeks, or possibly months, then you must prime the oil filter.

The 7.5 qt Champ oil pan has kickouts that swell outward approx. 3 inches on each side. If you think you will encounter clearance issues with the kickouts, we recommend opting for the stock appearing 6 qt. oil pan. The 6 qt. pan will still be a Champ pan and will have the windage tray and crank scraper. We strongly recommend reducing the amount of oil used in these oil pans by approx. 1/4th to 1/2 a quart. Doing this may greatly reduce the chance of oil leaks, and reduce oil temps. The larger counter weights used on stroker crankshafts are why we recommend reducing the oil capacity in these engines.

To be clear on what we're saying, we would like to see you add right at 7.0 to 7.25 quarts of oil grand total in your engine and oil filter when using the higher capacity oil pan. When using the stock appearing oil pan, we would like to see you add right at 5.5 to 5.75 quarts grand total in your engine and oil filter.

Our engines include a dipstick. It's very important that you re-calibrate the oil level marking on the dipstick. This is due to the fact that the dipstick, oil pan, and block are all made from various manufacturers and we often see great variances. Couple this with the fact that you may be running a reduced amount of oil, and the "full" mark on the dipstick will most likely not indicate correctly. Once you have put a predetermined amount of oil in your engine, and run it for a few minutes, let it sit for awhile on level ground, check the oil, and mark your dipstick with a flat file to re-establish the full mark.

More tuning recommendations. Very important.

You must be sure that your air to fuel ratio is correct. We strongly recommend purchasing a fuel to air ratio monitor. Proper carb jetting is also a must. If you purchased the dyno package from us then the fuel to air ratio on your carburetor will be tuned within the safe ranges.

If you are using your own carb. on this engine, then you must be sure the fuel to air ratio is correct. If your carb is running too lean, detonation is at your door.

If it is excessively rich, cylinder wash-down from excessive fuel will destroy your bore finish, pistons, and rings quickly, not to mention cause excessive fuel consumption.

A tad on the rich side is not a problem and can help resist detonation; a tad on the lean side will generate the most power and increase fuel mileage.

The optimal air to fuel ratio is approx. 13:1 Set total timing at 30-34 degrees. Total timing refers to the reading at 4500 rpm with the vac. advance disconnected. The closer to the lower number (30 degrees) the total timing is, the safer your engine will be. Do not worry about initial timing, as it will be determined by the total timing.

You may try running the vacuum advance if you have our regular HEI in this engine. Cam choice 1 may not allow proper operation of this, but the smaller cams may work well. The vacuum advance is adjustable and we recommend that you try it out. If you feel the vac. advance is putting too much initial timing into the engine, you should be able to adjust some of this out of it. Most aftermarket HEI units have an adjustable vac. advance. When setting the total timing, do not have the vac. advance hooked up. If you can bring your initial timing up from where it is at idle by running the vac. advance, the engine will operate tremendously better, have much better fuel mileage, and run cooler in most vehicles. Being able to run the vac. advance with good results is dependent on many factors.

If you hear valve clatter/ping (as it's called), then you need to try and adjust this out of the vac. advance. If valve clatter (pinging, as it's also known) is present under load, then you may not be able to run the vac. advance, but if the valve clatter is coming in around 3500 rpm or higher, then this could be a sign your total timing is set too high. Try backing it off a few degrees before giving up on the vac. advance. Valve clatter/pinging is actually the sound of the detonation occurring in the engine, and can be very damaging.

Be sure to have a high amperage battery and high quality starter. The battery must be 850 cca or more. Use heavy gauge battery cables. If you have a hard cranking issue, purchase an in-car timing controller or ignition kill switch. This will allow you to control your timing for optimal performance and ease of starting.


Do not run regular gas in this engine, no matter how much you have reduced the timing. It may not be enough! You may have run an old car in the past that pinged and clattered under load for many miles, and this didn't seem to hurt it. Most cars from the 60's and 70's had very low compression, especially when nearly worn out, and this is why the detonation did not destroy the engine. Excessive pinging, spark knock or valve clatter, as it's often referred to, may destroy this engine very quickly. Light pinging now and then is unlikely to do any damage, but it certainly will when there is an excessive amount of it under load.

Let any engine with compression numbers above 10:1 clatter and ping for very long, and you will lose the engine due to detonation, and in some cases this can happen very quickly.


Spark Plugs: We recommend the Autolite brand, part number Autolite 3923. Most of our engines include the correct spark plugs. We also offer a premium NGK plug that is highly suitable for this engine when running in very hot climate. Race grade plugs are fine as they have a few features that are desirable for certain types of driving. Keep the temp in the low to middle range. Use a plug that's too hot, and you are once again close to detonation/pre-ignition; use a plug that's too cold and they will foul constantly, run poorly when cruising at low speed, and be difficult to start.

Most of our engines come with spark plugs in them, depending on the package you purchase. You may also use NGK part # NGK 4544, a plug that is one step lower in heat range than the Autolite plug. The NGK plug is only to be run during very hot weather.

You would be amazed at how much better an engine will run with the correct spark plugs installed, but brand name has little do with this. It's more to do with heat range than any other factor. Factors such as outside temp, altitude, compression ratio, and the type of driving you do determine the temp range to run.

A slight loss of power is also an issue with plugs that are too cold, as well as possible difficulty in starting. However, you can have much more serious issues by running plugs with high temp ranges.

Keep the engine coolant temp as low as possible, but it is not a problem if it runs as high as 210 on very hot days, as long as it's consistent, and not climbing.

Never use pure antifreeze. 50/50 mixture or even slightly less antifreeze will cool the engine better than a rich mixture of antifreeze. Keep the engine temp down if possible, but don't worry if you can't get it below 210 on a hot summer day. The cooler you keep the engine, the lower the risk of detonation. Set engine idle at approx. 900-950, and never too far below this unless you are running our cam choice three. The reduced size cams would allow for a lower idle speed.

Never let the engine idle for excessively long periods during the break-in period.

Do not overfill with engine oil. Slightly less than normal is better than too much, in most cases. Using half a quart less oil can greatly reduce potential oil leaks. This is a common practice in many high performance engines.

When setting your carb choke, we recommend setting it on the mild/lean side. It is best for the choke to open up to its full straight up position as quickly as possible. Keep backing it off until cold starting becomes difficult. Quickfuel brand carbs are best to run. They are also suitable for use on engines running a mechanical or electric fuel pump.

If the choke is set up on the aggressive side, it will create an over-rich condition upon every cold start-up and warm-up. This over-rich condition is very damaging to an engine, and will waste fuel.

If you feel you can get by without using the choke, then by all means do without it! The modern day carbs actually do well with very little or no choke. With a few pumps of the throttle and a bit of feathering, the throttle will have you off and going smoothly, in most cases with very little or no choking at all.

Hydraulic roller setups are virtually maintenance-free and require little if any maintenance.

Our recommendations will change from time to time. We never stop trying to build a better engine, and we learn from our own experiences and from feedback from our customers. We know there's always room for improvement. We're always working on research and development, as does any successful business. We advise checking out the recommendation section of our engine ads on a regular basis.

Why have we given such detailed information on our warranty and maintenance suggestions? Some customers bought our engines and did not fully understand our warranty and the maintenance needs of the engines.

Not knowing is understandable, but failing to educate yourself on the do's and don'ts is asking for problems. We suggest joining a few good car forums, as they have a wealth of great information.

However, beware of some individuals on forums who think they know it all, and really know very little. Do your research using several sources, and be sure to read between the lines.

Special note.

For engines equipped with special order solid roller cams, the warranty on the valve train components is for 30 days. You may never have a problem with any of the components, but excessive street driving at cruising speed can adversely affect these components.

Solid roller setups on BBC engines should not be driven for excessively long distances or for long periods of time on the street. A weekend of racing at the drag strip would likely have less of an effect on the valve train components than a 100 mile easy drive.

If you do think you will be driving significant numbers of miles, we strongly recommend staying with our hydraulic roller cam package. The warranty on the hydraulic roller cam and valve train components is the same as the rest of the engine. See our other listings for info on all of our engines.

Important notice.

This engine does not include a fuel pump. This engine is best suited to operate with an electric fuel pump, with a pressure regulator set at 6-6.5 psi. A chrome block off plate will be installed on the engine. We believe that the electric fuel pump system is a superior fuel delivery system compared to a mechanical system.

Skip White

Your engine info will include the balance sheet and other information on this engine such as cam card, and your invoice will show your personal selection of the options offered.

Many have asked why we're able to sell such an engine for such a great price. It's because we're a major distribution center for all of the parts used in this engine, as well as a full scale machine shop. Our purchase price for the parts used in this and all of our engines are at master warehouse distributor (WD) pricing. Few machine shops ever get to master-wd pricing. We also believe in keeping our profit levels low enough to allow the working man a chance to build his car the way it should be built.

Transmission Recommendations

Your selection of what type transmission you're going to use with your new engine is very important. I'm going to give you the real lowdown on what transmissions I recommend, as well as the ones I would stay away from. For those building a very mild, (detuned) street rod, (small cam choice, dual plane intake) these recommendations are not as critical.

700R4: Worst possible transmission choice.

Pros

  • None, other than there are plenty of them around for a cheap price, and for good reason.

  • Fuel injection does make this trans. more tolerable.

  • It will get you from point A to point B period!

Cons

  • Very wide first to second gear spread. First gear is a 3.06 ratio Second is a 1.62 ratio. This nearly equates to skipping from first to third gear with a manual trans. This kills acceleration when these trans go into second gear on a carbureted engine with a healthy cam and large runner intake manifold. Compare this to a TH350. First gear at 2.52 ratio and second gear is 1.52 do the math.

  • The 3.06 first gear is so low that any final gear of above 3.55 or numerically higher will have you right at the max rpm at around 35 mph, only to then have your car fall on its face when it hits second gear, feeling like it skipped a gear. Wheel spin is uncontrollable upon hard launches, unless you have a very tall final gear, and then you can for sure count on going nowhere quickly when second gear comes in. Overdrive would be totally useless at highway speed regardless of detuning with a tall final gear, unless you were cruising at around 100 mph.

  • Huge cost to build up to a decent street rod level. Don't even consider a stock rebuild to handle 500 hp or more. Under hard use, the 700R4 will fail quickly.

  • Limited as to what level these can be built up to. High performance transmission builders and parts suppliers don't even recognize this as a serious transmission.

  • More complex to build than a TH350 and far more expensive, especially when built up to handle high hp numbers.

  • Having to run a cumbersome throttle value cable to the carb. linkage. This feature actually serves a good purpose, but if not set properly, it can destroy your transmission quickly. Very critical adjustment, and often overlooked.

  • The overdrive is actually useless with engines running decent size cams relative to the cubic inch, especially with large runner dual plane intakes, and single plane intakes are out of the question with this trans.

  • Stall converters are double the cost of the one run in a TH350.

  • This is not a reliable transmission in a street rod.

  • Lowers the value of your vehicle to some degree, especially on high hp builds. These transmissions do not belong in most carbureted street rods. You must detune an engine considerably to operate the overdrive and be able to tolerate the first to second gear drop.

  • Could be classified as the worst mismatch of parts known on a true street rod.

  • As a side note, I would like to mention that most of us have owned a regular stock street car with a 700R4 trans, or its electronic likeness, a 4L60E, and didn't find much of an issue with the way they operated, especially if the vehicle was fuel injected. This is because stock car engines are designed to operate totally different in the very low rpm range. They have huge amounts of off idle torque compared to the average carbureted street rod that makes 400 hp or more. This off idle instant torque allows the vehicle to keep its speed up decently when the 700R4 drops into second gear, and the same low rpm also allows the overdrive gear to operate normally at very low rpm. There are other factors that also allow these trans. to operate at low rpm, especially on fuel injected computer driven engines.

TH350: Best transmission choice, hands down.

Pros

  • Excellent gear spread between all three gears.

  • Very low cost to build up to various levels of power handling.

  • Can be built up to extreme power handling capabilities.

  • Most all transmission shops are capable of building these to at least level 1 or 2.

  • No TV cable to deal with.

  • Stall converters are low in cost, and the selection is broad.

  • Very reliable and simple to repair if needed.

Cons

  • None, simply none! Select a final gear that will allow you the best overall performance and one that allows a decent off the line acceleration, and one that will be in a tolerable rpm range at highway speed. You must have the correct stall converter for optimal performance. This can make a huge difference in the way your vehicle accelerates.

  • These are becoming scarce, but there are still plenty of them around, and high performance parts are easily obtained.

  • You may have to go through this long story to your less than knowledgeable friends as to why you didn't choose a 700R4, and when you explain it to them, they may still think you don't know what you're talking about.

TH400

Pros

  • Excellent gear spread. Very similar to a TH350.

  • Strong internal parts.

  • Reliable.

  • Simple to build or repair to stock buildup levels.

Cons

  • Very expensive to build up to higher power handling levels, as compared to a TH350. The TH350 has far more high performance parts available at reasonable costs. The 400 trans. is not a practical choice.

  • Internal rotating parts (cast iron drum) are very heavy and create a huge drag compared to most any other trans., and this is not a subtle amount of drag. The TH400 is well known to be a heavier duty trans. than a TH350 but this heavy duty factor was designed more for heavy vehicles that may encounter pulling heavy loads. Only the largest of the GM cars weighing around 5000 lbs had these trans. in them, along with heavy duty pickups, usually 3/4 ton or larger trucks. Even the half ton Chevy trucks didn't come with these in them.

  • They will certainly hold up better than a stock built TH350, but they are not a desirable trans. for a street rod. You can build a TH350 to level two that would be superior to any stock TH400 in every way for about the same cost. Building a TH400 to a high hp handling level will cost a great deal of money.

  • You will never see this trans in a true Pro-Street car.

Powerglide.

Pros

  • Excellent transmission to build up to just about any power handling level.

  • Most trans. shops are able to build this trans with ease.

  • Very reliable, and simple to work on. Not much to go wrong.

  • Decent first to second gear spread.

  • Rotational drag is very low with this trans., moreso than any automatic on the market. Very efficient trans.

  • Stall converters are not expensive and many choices available.

Cons

  • Two gears, that's the problem. This trans. can only be run in cars that have a very high hp to weight ratio. It would be fair to say a vehicle weighing approx. 3400 lbs would require an engine output of 1000 hp or more to make it a rational choice, and even then, you would still need a decent final gear to get things moving off the line. The first gear in these is somewhat tall. Those running a T-Bucket roadster weighing around 1800 lbs. with a 500 hp or higher engine could make great use of a Powerglide trans.

  • Having only two gears limits having the best of both worlds when it comes to off the line acceleration and cruising at highway speed.

GM200

Pros

  • Has a better gear spread than the 700R4 but not as optimal as the TH350.

  • Not much good to say about this trans. It certainly has a place in some special late model applications, but old school Chevy engines is not one of them.

Cons

  • This transmission can cost up to three times more to build up to a decent power handling level compared to a built up TH350.

  • Cannot hold up to high torque engine builds unless an enormous amount of money is spent on this trans.

  • Most all the cons you see for the 700R4 exist within this trans.

  • This trans is not a reliable trans. compared to any of the early GM trans.

4L60E Electronically controlled trans.

Pros

  • No TV cable to deal with or shifting linkage. It has pump pressure control and shifting via electronics.

  • Not much good to say about this expensive trans. It is virtually a 700R4 with a modern twist.

Cons

  • Most of the same issues as the 700R4. Terrible choice to run in an old school carbureted engine.

  • Very expensive to build up to a high power handling level. Can cost up to $4,000 to build this trans up to a decent level. Computer controlled engines may require this unless you bypass the car's computer system.

  • Complex. Very complex!

  • Pointless to run such a terrible transmission.

  • If you insist on such a trans, the 4L80E is a better choice, as it has a normal gear spread, and is a much stronger trans. Still pointless to use with an old school carbureted engine.

Four and five speed Manual Trans.

Pros

  • Excellent acceleration at any speed due to many selective gear ratios. Finding a gear at any cruising speed to hit it hard is easily accomplished with a manual compared to an automatic.

  • More efficient delivery of horse power to the rear wheels with a manual trans. versus an automatic. In other words, less loss of power due to slippage as encountered with an automatic trans.

  • For some people, the fun factor of shifting gears is one of the high points of owning a street rod.

  • Very reliable, long lasting. Low maintenance. Simple to change out a clutch if needed.

Cons

  • Can be very expensive to purchase a high quality modern manual trans. and high performance clutch and flywheel, especially the Tremec Series.

  • Can be somewhat complex to change over from an auto to a manual trans.

  • If you think your car is going to run faster with a manual versus an auto, you will be greatly disappointed. The automatic transmission can not only shift much faster, but off line acceleration can be controlled to a much greater degree. This is why most drag cars have automatic transmissions. All things equal, a car equipped with an auto trans will outrun one equipped with a regular street rod manual with great ease.

  • Missing gears when racing can cause damage to your engine, and loss of control of your vehicle should you drop into the previous gear during an aggressive run. Been there a couple times, dropped a valve in brand new Lotus Esprit shifting out of second into first rather than third, and locked up the back wheels on a Dodge Viper shifting into second rather than fourth at high speed. Nearly lost control of the car at around 80 mph.

  • If you're deciding to run a 5 or 6 speed manual trans because of the overdrive gear, be aware that most engines built with large lopey cams, and single plane intakes running a carb will usually not allow effective use of the overdrive gear.

  • Tremec T56 transmissions are very popular and highly advanced. They are expensive. They tend to be notchy to shift when new. Takes many miles before they become easy to shift. They can be difficult to install in some early model classic cars, as they are huge compared to early model transmissions. They can cost a great deal of money to rebuild if needed. Still about the best manual trans out there, and can handle very high hp levels.

  • Sadly, your wife may not be able to drive your car with a manual trans. This could be a plus in some cases.

A final note.

Our user id is: skipwhite, and our store name is whiteperformance1. You may have noticed other sellers using a similar name offering similar products. These other sellers have capitalized on our name as we see it, and many customers searching for us will inadvertently find them, thinking we are one in the same company. There is only one "Skip White" We are the original premier seller under this name since approximately 2002. We have no other names, nor are we associated with any other company regardless of the similarity in the name or location. Our official company name is Skip White Performance.

THE NEW BBC TURNKEY ENGINE WITH A CVF V-BELT SYSTEM photo b4cde475-8710-46e5-8ec7-db8a85702020.jpg

Note from Skip White, President.

I have reviewed similar 454/468 engines on the market, and I've found many of the parts used to be substandard and overpriced. When I use the term "substandard," I mean relative to the price charged. However, some sellers have parts in their engines that are prone to failure in our opinion. The machine work or lack thereof on many of these blocks may also pose a problem. Many vendors sell BBC engines at similar prices, but most of them use crusty old 454 blocks. These 30-40 year old blocks are past their prime and, even when they were new, made a very poor foundation for an engine generating double the original horsepower. If you see the term "seasoned block" in the build parts list of an engine, that is indicative of of an old junkyard block that's seen many hard miles.

For the most part, many of the components used in our engines are far from the lowest cost version on the market. They are in the middle ground, or better. This is why I feel it necessary to mention all of the items in detail used in our engine, as I feel they make the difference in reliability and longevity.

If you want to make a true comparison, then you should request a full build sheet, including brand and the actual part number or description of all parts being used, from our competitors. Some of the items used in this engine are actually lower cost/lower grade, but have nothing to do with reliability or longevity of the engine. These lower cost items keep the price reasonable but do not compromise reliability.

For those wanting a higher horse power engine, see our other listings.

We have the most advanced machinery available on the market. Our Centroid DRX block and decking machine cost $80,000. We torque plate hone the cylinder walls using a state of the art Sunnen SV10 diamond hone. Very few shops have this model. It not only produces a superior bore finish that allows a faster break-in time, but it also creates a very straight and uniform finish with virtually no distortion or variance in the cyl. walls. This machine cost us approx. $60,000. Most of the very high end engine builders are now using this model.

Those offering high performance engines for sale and not disclosing what machines are used on them is unsettling to me. Many of our customers have asked if they can tour our shop before buying an engine, and we certainly welcome this.

A final note.

Our user id is: skipwhite, and our store name is whiteperformance1. You may have noticed other sellers using a similar name offering similar products. These other sellers have capitalized on our name as we see it, and many customers searching for us will inadvertently find them, thinking we are one in the same company. There is only one "Skip White" We are the original premier seller under this name since approximately 2002. We have no other names, nor are we associated with any other company regardless of the similarity in the name or location. Our official company name is Skip White Performance.

Customer Reviews

This product does not have any reviews yet.