|Product Type||Shipped Product|
|Number of reviews||0|
BBC CHEVY 632 CUBIC INCH DRAG SERIES ENGINE 1050 HP AT 6700-6800 RPM
855 ft lb of torque at 6800 rpm.
The engine shown above is an actual representation of the engine you will receive.
RUNS ON 110 OCTANE RACE FUEL. JE FORGED CUSTOM PISTONS AND SCAT 4340 FORGED CRANK AND H-BEAM RODS, WORLD MERLIN IV BLOCK, AFR FULL CNC'd 385cc ALUMINUM HEADS
This engine uses a tall deck block (10.200)
FULLY ASSEMBLED FROM INTAKE TO OIL PAN
The build sheet is at the lower part of this listing. This engine is designed for high performance pro street rodding or strip use.
This engine uses a brand new World Merlin IV block, with a tall (10.200) deck height.
The block is bored to size with our new Centroid touch probe machine. Few machine shops have a machine of this accuracy.
We also deck the blocks to an RA finish of approx. 15 or better. The decking procedure is also done by our Centroid CNC machine.
We often find many brand new blocks to have a sloping deck of up to 4 thous. When we're finished decking the block, it is within approx. .001 accuracy from end to end. Many machine shops fail to catch this as the machinery they use does not allow for such accuracy.
We then plate hone the block with our new Sunnen SV10 diamond hone machine. This is also a very advanced machine that hones the block with a finish unlike conventional machines.
The final step is to clean the block in our high pressure block washer.
BBC WORLD PRODUCTS MERLIN IV BLOCK BORE 10.200" TALL DECK HEIGHT
We now use the Merlin IV blocks in our BBC 632 engine builds. The Merlin block is light years ahead in overall construction as compared to any of the other blocks on the market. The main caps all have ARP hardware. Dimensional specs are spot on, and this has been an issue with other blocks we have used in the past. Many of the top engine builders, ourselves included, have found the new Merlin IV block to be superior to the earlier generation Merlin III block in many ways.
World Products has completely redesigned the famed Merlin Big Block Chevy casting, incorporating numerous improvements and new features to virtually every area of the block.
Designated the Merlin IV, this new block is offered in all popular sizes and deck heights and is sure to be a favorite among racers and professional engine builders.
Below are the specs of the rotating assembly portion of this engine.
The picture above is a file photo of the rotating assembly that comes with this engine. See the detailed info below for the actual pictures and items included in this engine.
Fully balanced in house.
Connecting Rod Specs.
Piston & Ring Specs.
Bearing, Damper, and Flexplate Specs.
Listed below is a complete breakdown of all the parts that are included in this engine.
JE CUSTOM MADE FULLY FORGED PISTONS. JE PISTONS ARE 100% MANUFACTURED IN THE USA. THESE ARE CUSTOM BUILT AND HAVE LATERAL GAS PORTING. TOOL STEEL GRADE WRIST PINS.
The JE forged pistons are rated very high in the street/strip performance industry. They
are made using the 2618 aircraft alloy and have fully machined crowns. We prefer the 2618 alloy over the lower cost 4032 alloy. This alloy may fragment from the effects of detonation and if this happens, it can be very destructive to the engine.
Those types of pistons are fine for stock or mild engine builds, but should never be used in carbureted engines built to high horse power levels.
The forged 2618 alloy piston is much more resistant to the effects of detonation and heat.
The wrist pins that are included are made from a tool steel grade material, and have thicker than normal walls. This is a very expensive type of wrist pin, and capable of handling very high amounts of horse power.
Our JE Forged pistons are custom designed with an increase in compression height. This has many advantages. Here are a few facts about compression height and deck height.
Our custom made pistons have a compression height that is .010 taller on bbc pistons, and .015 taller on sbc pistons, as compared to most all of the catalog pistons on the market. We find this to be a very valuable feature.
Since our pistons sit at a taller than normal compression height, we only have to remove approx. .005-.010 off the deck surface of the block. Our goal is set the piston at zero deck (flush with the deck surface). This maintains the deck's thickness, making it much stronger than a block that has been cut down .025. The engine will also run a bit cooler with a thicker deck. It's well known that the deck dissipates much of the built up heat an engine generates. This also allows for future deck re-surfacing without compromising the integrity of the block. On our bbc engines, we actually leave the piston about .003 to .005 in the hole to allow for possible piston rock. Our sbc engines will have the pistons setting right at zero with the deck.
These pistons are also suitable for use with nitrous or blower setups.
Scat 4340 Forged Crankshaft.
The picture below is a generic file photo of a Scat crankshaft.
Some of the benefits of the Scat crankshaft supplied with this assembly:
The material used in this crankshaft is manufactured from an exclusive Space Age material that was designed for high strength and fatigue resistance. The Scat cranks are the best value you will ever find. The Scat crankshafts are the best way to build a strong bottom end for, street rods, dirt and circle track racing, and drag strip racing.
Pictured below is our ABS crank polishing machine in action. We polish the crank on every engine we build. This extends bearing life, keeps oil cooler, and with the reduced friction, a slight increase in horsepower is gained. Many machine shops fail to do this. The finish on most cranks are at the bare minimum of acceptance, and we know this can affect bearing life. We have measured the RA finish with our profilometer, and found it to be as high as 25 RA finish on many of the cranks. We bring that number down to below considerably.
Genuine Scat brand heavy duty 6.700 H-beam rods with ARP L19 cap screws.
We use genuine Scat rods with ARP cap screws in all of our engines. Our Scat rods are bronze bushed, and unlike Eagle I beam rods, these are fully forged 4340 alloy.
We have noticed some engine builders using low cost generic rods and crankshafts in their engines. These non-branded, (no-name) products are often poor quality in many ways. You will notice many of the low end engine builders fail to mention the actual brand of the rods or cranks used in their engines. Upon further investigation you will find such parts not to be a branded name product. They may label these parts with a name, but one that is totally unrecognizable in the industry. Our experience in years past with such rods and cranks has been disappointing to say the least. Besides the obvious issues such as incorrect sizing and machining that is difficult to correct, the questionable alloy these items may be produced from and the potentially incorrect heat treating methods used, could prove to be disastrous. Little can be done to verify this and nothing can be done to correct it. Failures of such critical parts will usually result in catastrophic damage to the engine. As you may have noticed, this is why we specify the brand name, and series of every part used in our engines.
Many of the inferior "no-name" rods on the market will also have "no-name" rod bolts in them. We have seen these bolts before, and they are very low quality. They don't have ARP's rolled thread design, and they don't torque down with the same characteristics as a genuine ARP bolt. It's not just a matter of having a different brand bolt in the rods; these bolts are low quality in many ways. They have been known to fail in engines to a much greater degree than a high quality rod bolt, and this failure usually causes catastrophic damage in the engine. Beware of rods that don't mention the rod bolt brand. As far as we're concerned, ARP bolts are the only brand we would ever use or accept in a set of rods.
Genuine ARP L19 cap screws.
We now use the Clevite bearings in our engines.
ATI SUPER DAMPER SFI INCLUDED.
INTERNALLY BALANCED, SFI rated, 7.074" DIAMETER, REDUCED ROTATIONAL MASS, OFFERS EXCELLENT CLEARANCE.
HEAVY DUTY SFI RATED FLEXPLATE MADE IN THE USA INCLUDED.
This SFI flexplate is made in the USA and will resist cracking and warpage to a very high degree. One good telltale in identifying a low quality flexplate is the lack of welding on each side where the plate mates to the ring gear. They usually have a pale grey color to them, as they are not coated, and will rust quickly. Ours are welded on both sides, and are much thicker than an OE plate, and are zinc dichromate coated.
We do offer this engine with a manual flywheel. In most cases we do have both sizes, 153 and 168 tooth, available.
Our CWT 5500 Balancer.
We do our own balancing with our new state of the art CWT 5500 Series balancers. The CWT 5500 is the ultimate for precision balancing. We now have three of these in our machine shop. We consider this machine to be highly advanced compared to the Hines balancer we once used. We balance every rotating assembly we sell within 2 grams or less at no extra charge. A balance sheet is included with your assembly.
Three CWT balance machines under one roof is a rare sight.
Our crew wrapping up for the day. Pardon the mess.
AFR fully cnc'd aluminum cylinder heads. 385cc runner size with titanium retainers.
The pictures of the AFR heads are a file photo of our regular AFR heads used on other motors. This engine will have the 385cc fully cnc'd heads with titanium retainers.
GENUINE AFR STUD GIRDLES.
File photo. Actual appearance may vary.
We use premium pushrods in all of our engines. They are made in the USA from 4130 chromoly steel. Regular hardened pushrods will most likely flex in the engine when running above normal RPM ranges, and risk bending under high RPM. These pushrods have extra thick walls.
Cometic premium race grade series head gaskets, ARP head bolts, and rocker studs.
Edelbrock Victor II single plane intake # 2897
304 STAINLESS ALLEN HEAD INTAKE BOLTS ARE USED ON ALL OUR ENGINES.
Comp custom ground cam.
Part number: Special Grind. Solid Roller.
Peak advertised hp of 1050 would come in around 6700-6800 rpm. The carb used on our dynoed test engine was a 1425 Dominator.
Below are our dyno results on our 632 engine with a single plane Super Victor II intake and a Holley 1425 cfm Dominator carb. We have chosen to advertise our hp numbers in the ad on the conservative side due to changing factors such as weather or other factors beyond our control. The correction factor in the dyno program is not 100% perfect, and less than ideal weather during testing can skew the results by a few hp plus or minus. Our brand new Super Flo dyno is very accurate, and set to factory standards. We actually ended up making right at 1081hp after a few more tweaks to the carburetor and the rpm only went up to 7,000. Considering this is such a long stroke engine I personally would like to sacrifice a few hp and keep the rpm in the sub 7k range.
Official Dyno report on our 632 engine with this cam and a single plane intake.
BILLET ALUMINUM TIMING POINTER. VERY FEW SELLERS FINISH OFF THEIR ENGINES AS WE DO.
We did not offer this billet timing pointer in the past. However, we noticed that there was a birds-eye view of the timing pointer from the driver side of the engine, so we decided to use these on all of our engines.
As you can see in the picture below, these timing pointers have a glove like fit.
We strongly recommend that you run a vacuum pump on this engine. We will supply the non-accessory hole valve covers with this engine if needed.
Timing components: Rollmaster billet double roller timing set.
Polished Aluminum Timing Cover.
We use the top of the Rollmaster timing set with a torrington bearing and rolon chain. The difference in quality is dramatic compared to the common low-cost timing set. The both sprockets are made from billet steel. This is a nine keyway timing set. These sets are hand matched for selective sizing.
The cost on this high end timing set is approx $115.00, more than double the cost of the low level budget timing set used by many other engine builders. Should you ever want to confirm that this is what is actually in your engine, you can remove the timing cover, and you will see that this timing set is very different in appearance to the run of the mill low cost sets often used by others.
This timing set is offered in three different chain tension setups, allowing us to set it up perfectly every time. One more benefit is that timing accuracy is very precise and will remain that way. This timing set will likely last for the life of the engine. This is what you will find in most solid roller engines, as they have very high spring rates, and create an enormous load on the chain and gears, compared to non solid roller setups. It may seem like a bit of overkill to use such a high end timing set, but the versatility and extreme quality outweigh the cost, in our opinion.
COMP ULTRA PRO MAGNUM XD ALUMINUM ROLLER ROCKERS
The picture above is the non-XD series. This engine will have the XD Ultra Pro Magnum rockers.
The new Ultra Pro Magnum XD™ Roller Rocker Arms not only live up to the lofty standards of the original Pro Magnums™, but they also take stud mount rocker performance, stability and value to a whole new level. The modern arched, web-like design delivers increased strength and rigidity while still reducing the moment of inertia and optimizing the dynamic balance.
If you’ve read our warning on engine builders using low grade no-name rods and cranks, a very similar situation exists in the roller rocker market. We do not use or sell off-shore, (no-name) roller rockers, period. They have proven to be faulty in many ways. The center trunnions are not polished, nor is the center of the roller tip true to size or polished. Metal fragments are often left inside the trunnion housing and will cause destruction of the needle bearings. The aluminum alloys used are never aircraft aluminum alloys as are used in all USA made roller rockers. They often mention the alloy as being 6061, and that is a very soft form of aluminum. The 6061 alloy used on these will assure rocker-flex on any higher than stock spring pressures, and this will affect performance. The pins and keepers that hold the parts together are often of poor quality and improperly installed. The front roller will usually scoot along the valve tip, as it can't roll properly due to rough internal surfaces.
We have honestly seen valve tips that were scalloped out due to the front roller dragging across them. This will cause the valves to side-load against the valve guides in the heads and surely cause damage to them if run like this for very long.
We have scrutinized these products in the past and found all of the above problems, and I can tell you there are most likely many more. We would not use them in an engine under any circumstances. You will also see many of these rockers made from stainless on the market. They use a very low grade stainless that actually has a near non-existent amount of nickel in them, but that's not the real problem with them, as stainless steel has no advantage over high grade heat treated steel when it comes to a roller rocker. The lack of hardness of the rocker body is the real problem. The problems with these stainless rockers are the same as mentioned above. These are the roller rockers you see on the market for around $119 and up to $169 for the so called stainless ones. They are pure junk, in our honest opinion. They could possibly be used on a budget back yard stock build up that has a very low spring pressure, with a cam that has very low lift, but then you would be better off with the stock stamped rockers on such a build.
We have heard of many engines using these rockers that came apart and spilled needle bearings into the engine, only to end up in the oil pump. It seems like some engine builders do not care how long the parts in your engine last, or they simply don't know this. I can tell you for sure that using such low grade, "no-name" roller rockers is asking for trouble.
We use Scorpion, Comp Ultra Pro Magnum XD in this engine. The difference in these compared to the low grade no-name rockers on the market is huge. Do a Google search on this subject and you will know then what we’re talking about.
Champ premium oil pan.
The oil pans we use on all of our engines are made in the USA by Champ. The Champ oil pan has a full windage tray, crank scraper, and trap door. Threaded dipstick is included. Extreme duty pickup designed not to fail. The oil pan is made from a thicker than normal gauge material, and has embossed ribs in the body.
This is an extended capacity oil pan. The special pickup tube is designed for this oil pan. If you think you may have a clearance issue with the 8 qt pan, let us know and we can use the stock style pan.
The 8 qt pan is approx half an inch deeper than a stock pan, and the kickouts on the side are at the lower section of the sump. They start to swell outward about three inches from the bottom, approx. 3 inches or less on each side. Most vehicles have no problem with this type of pan and it's certainly a much better setup than a conventional oil pan.
The quality of these pans far exceeds any of the lower priced oil pans used on many engines.
We do not use the knock off oil pan gaskets on the market. Felpro premium oil pan gaskets are used on all of our engines.
Pictured below is a file photo. The actual Felpro gasket used will be the correct model for this application.
Studded Mini Nut Set.
We use our premium studded mini nut set on all of our oil pans and valve covers. The nuts have a serrated face and built in washers. This is the ultimate set for securing the oil pan and valve covers to the engine and is far superior to the typical bolts used by most other engine builders. Our standard engine color is black. Custom paint work on engine blocks and oil pans is available as an optional upgrade. The pictures above and below are file photos to display the studded mini nuts. Other items seen in these pictures may not represent your actual engine.
Melling M-Select Oil Pump, and M-Select Drive rod with ARP stud.
The M-Select series oil pump by Melling has several important upgrades compared to the regular Melling M-55 Series. The gears are billet steel, and the body is stronger, coated with corrosion-resistant nitrite. This oil pump also includes the M-Select drive rod. Both components are far superior to the regular Melling oil pump and drive rods used by most other engine builders.
We are confident that the price we have on our engine will never be matched by our competition!
We include an engine lift plate and heavy duty engine stand with casters with every engine we build.
As with any race grade engine, this engine will not have a basic warranty. We will warranty our workmanship, and any parts used in this engine will carry the warranty offered by the manufacturer only.
Your carb should be tuned to allow the correct fuel to air ratio. This ratio can vary depending on many factors such as altitude, vehicle weight, gearing, type of driving, etc. These values should be in the recommended safe zone.
Continue reading for more detailed information on timing and carburetion. You must follow the oil recommendations listed below.
Oil pressure of 50-60 lbs in the upper rpm range on a fully warmed up engine is nothing to worry about. You may also notice that oil pressure drops at idle to approx 25-30 lbs when the engine is fully warmed up during very hot weather. This is somewhat common and no cause for alarm.
If your engine has a Merlin IV block, then it has priority main oiling. This block routes the oil in a very different pathway compared to a GM block. The mains and rod bearings as well as the crankshaft are well protected with an ample supply of oil even when the oil pressure numbers are lower than you think they should be.
There are many special additives in race grade oils that are not in conventional oil. These additives are very valuable for high performance engines. Never add anything to racing oil. This oil has exactly what is needed to protect a high performance engine. Some of these oils will state that they are low or possibly non-detergent, and that is a desirable trait of racing oil.
The anti-foaming agents in race grade oils are much better than what you would find in conventional motor oil. Race grade oils have higher than normal amounts of the zinc compounds in them, and there are many components in the engine that can make great use of these additives.
This engine does not include a fuel pump. This engine is best suited to operate with an electric fuel pump, with a pressure regulator set at 6-6.5 psi. A chrome block off plate will be installed on the engine. We believe that the electric fuel pump system is a superior fuel delivery system compared to a mechanical system. If you decide to run a high volume mechanical fuel pump on this engine, then you must use the special polymer fuel pump rod that we offer, and you must also use a fuel pressure regulator, and gauge, set to approx. 6.0-6.5 psi. Only use engine oils with high levels of zinc compounds in them when running a mechanical fuel pump. This will protect the eccentric fuel pump lobe on the camshaft. We strongly recommend the Schaeffer Racing oil. See our other listings for this oil.
As for oil filters, we recommend a high quality oil filter. Racing oil filters are excellent. See our other listings for the recommended oil filters.
Engine break in: As soon as your engine is installed, check and reset the timing if needed.
Drive safely please but keep your engine under load more than normal and bring the rpm up and back down to seat the rings much better and faster. This allows the rings to expand in a perfect circle and with greater pressure against the cylinder walls to establish an even wear pattern. This is why race engines are dynoed: to put a good number of passes on the engine under heavy load, as this will partially seat the rings very quickly, making the engine somewhat ready for racing. Failing to do this not only delays the break-in, but can permanently stop the engine from establishing a good wear pattern on the cylinder walls.
If you have opted for our dyno-tuned version of this engine, then ring seating will be partially established. The dyno has a computer controlled break-in mode that we use before doing any dyno testing for power output.You must replace the oil filter that is installed on the engine with a high quality oil filter, but opt for the medium length version, as this will help maintain oil pressure and volume much better than the short version. See our listings for the recommended oil filters.
Your engine booklet will include the balance sheet and other information on this engine such as, cam card, and your invoice will show your personal selection of the options offered. We usually mail this out prior to shipping the engine.
THIS ENGINE USES THE BEST PARTS. WE’VE REVIEWED WHAT THE COMPETITION IS OFFERING, AND WE’RE 100% CONVINCED WE ARE OFFERING A FAR BETTER VALUE.
Many have asked why we’re able to sell such an engine for such a great price. It’s because we’re also a major distribution center for all of the parts used in this engine, as well as a full scale machine shop. Our purchase price for the parts used in this and all of our engines are at master warehouse distributor (WD) pricing. Few machine shops ever get to master-wd pricing. We also believe in keeping our profit levels low enough to allow the working man a chance to build his car the way it should be built.
A final note.
Our user id is: skipwhite, and our store name is whiteperformance1. You may have noticed other sellers using a similar name offering similar products. These other sellers have capitalized on our name as we see it, and many customers searching for us will inadvertently find them, thinking we are one in the same company. There is only one "Skip White." We are the original premier seller under this name since approximately 2003. We have no other names, nor are we associated with any other company regardless of the similarity in the name or location. Our official company name is Skip White Performance. Please see the article below for a more detailed explanation.
The real story...Skip White Performance vs. White Performance & Machine
I'm sure many of you have noticed there are 2 high performance engine builders in Kingsport, TN with similar names, and this has led to a great amount of confusion.
We are Skip White Performance, NOT White Performance and Machine.
Due to the name similarity many customers looking for us online inadvertently find them, thinking we are the same company. Definitely not...there is no connection between the two companies. We don't have a problem with free enterprise (competition). However, when the competition builds their foundation on such things as a name similarity and their supposedly long history of being in business, then we think it's about time we set the record straight.
We have owned White Performance since 2003, with the exception of the machine shop, which was owned by Fred White at the time. He continued to operate the machine shop and build engines for us while we continued selling online under the user ID of skipwhite and the store name of whiteperformance1.
Due to their limited production capability and many disagreements about the engine building process and workmanship, we opted to open a full scale machine shop of our own a few years later. Fred White began competing against us even though our contract had a non-compete clause in it.
As our business grew, we opened a second, much larger warehouse and machine shop around 2011, located on Brookside Ln. in Kingsport TN. By putting heart and soul in this company, we have become the number one street rod engine builder in the nation.
Fred sold his shop to an investor in 2016 and the new owners continue to reap the benefits from this confusion between the two shops. This investor lacks any knowledge of this industry. They continue to use the White Performance & Machine name. Contrary to what is posted on their website, Fred White is no longer associated with the company in any way. Their main spiel in advertising is, "In business since 1979," when in fact, we purchased the White Performance company in 2003, with the exception of the machine shop.
All in all, we have been in this business 16+ years. Skip White's passion has been owning and building street rods for 47 years on a personal level. The knowledge he has gained over time has allowed him to venture into this business and succeed to a very high level.
The great pretenders continue capitalizing on our success due to the name similarity, but have been degrading our reputation. Recently, we have been getting calls nearly on a daily basis from people that now realize there are two shops in this town with very similar names. They complain of serious problems in getting their engines in a timely manner from them. They think they purchased their engine from us. Due to the confusion, there is an increasing amount of negative talk that is starting to reflect on our reputation within the street rod community, when in fact we have a near perfect reputation in this industry. We have an "A+" rating with the Better Business Bureau, and they have an "F" rating. That may change in the future, but they have had the "F" rating for several years, and we have maintained our A+ rating for many years.
FAST FORWARD TO 2019...We have become the largest street rod engine builder in the nation. Our engines, rotating assemblies, and cylinder heads are built to very high standards and shipped to our customers in a timely manner. We are a premier seller on with a positive feedback score of well over 206,000 and growing, as compared to our competitor’s score of approximately 24,000.
Our engines are custom-built to our customers' specifications and are shipped in approx. 2-4 weeks, perhaps sooner, depending on the season. Our rotating assemblies usually ship out in about one week or less, and our heads ship in about a week or less.
Now you know the real story, and we hope this helps with the confusion.
This product does not have any reviews yet.