SBC CHEVY TURN KEY STAGE 3.0 HYDRAULIC ROLLER CAM 406 CUBIC INCH WITH A CVF 8 RIB SERPENTINE ACCESSORY DRIVE SYSTEM. ENGINE 540 HP STREET ROD SETUP.
RUNS ON PREMIUM PUMP GAS.
The picture above is an outdoor shot. Those below were taken indoors.
The CVF 8 rib Serpentine kit is one of the highest quality setups on the market. All of the brackets and pulleys are made in the USA from billet aluminum. Many similar front accessory kits use a 6 rib design, and are made from cast/machined parts. We also offer this setup with an air conditioning compressor, and a power steering delete if desired. This accessory system comes in polished aluminum or powder coated black.
We also offer our engines with a lower cost basic front accessory kit, with electric water pump option and with no turn-key, (base) options at all. See all our engine listings.
The chrome plated one wire CS alternator has a 140 amp output.
Pictured below is an angled downward shot as the engine would appear when observing it in the car.
THE ENGINE IS COMPLETE AS SHOWN FROM CARBURETOR TO OIL PAN.
PLUG WIRES ARE INCLUDED BUT NOT INSTALLED.
Also available in black as pictured below.
DART SHP BLOCK WITH SPLAYED MAIN CAPS.
FORGED 4.155 BORE WISECO PISTONS, SCAT 3.750 STROKE CRANK, AND 6.0 SCAT RODS NKB ALUMINUM HEADS.
4.155" BORE X 3.750"
- DART SHP BLOCK WITH SPLAYED MAIN CAPS. COMMONLY USED IN ENGINES BUILT TO 800+ HORSE POWER.
- NKB 68cc ALUMINUM ALLOY HEADS WITH PBM COMPETITION SERIES VALVES.
-COMP HIGH ENERGY ALUMINUM ROLLER ROCKERS.
- COMP HYD. ROLLER CAM AND TIE BAR STREET STRIP ROLLER LIFTERS. A CUT ABOVE THE OTHERS.
- CLOYES RACE BILLET TIMING SET. THE VERY BEST CLOYES HAS TO OFFER.
- SCAT CRANKSHAFT, CLEVITE BEARINGS. BALANCED ON OUR CWT BALANCER TO BELOW 2 GRAMS.
- SCAT RODS WITH ARP 8740 CAP SCREWS.
- WISECO PREMIUM FORGED FLAT TOP PISTONS. 800+HP RATED.
- QUICKFUEL 4 BARREL CARB. SLAYER 600 OR 750 CFM DEPENDING ON CAM CHOICE.
- MELLING M-SELECT SERIES OIL PUMP WITH M-SELECT DRIVE ROD.
- CHAMP CUSTOM 8 QT. OIL PAN WITH OIL CONTROL SYSTEM.
- ALUMINUM WATER PUMP.
- PRO-RACE BRAND S.F.I. DAMPER.
- TWO YEAR WARRANTY.
Two year warranty, see details below.
This engine is designed to have a high level of drivability, or street manners. Cams #3 and #4 are our favorites for offering exceptional low end and mid range performance plus max drivability without needing to deepen final gearing or the need for a high stall speed torque converter.
If you choose to go with the Hurricane single plane intake and the first choice cam with 1.6 rockers, it will bring the hp numbers up to approx. 540. We do not recommend the single plane intake combined with cam choice 1 on any car that is over approximately 3400
Please read the cam info provided below on the four cam choices before purchasing this engine. It is very important that you choose the correct cam and intake for your car and its intended purpose.
Here are a few good reasons why we think the 406 engine is a better choice than the 383 engine.
1. The 406 will accelerate most medium to heavy cars dramatically quicker than the common 383's on the market. The main difference between a 406 and the 383 is that the 406 torque comes in much lower. The difference is so dramatic that you would estimate the engine to have a much higher horsepower rating than it actually has. If you're not familiar with the 406 engine, do an internet search on SBC 406 vs 383, and you will be convinced of the difference. There is no inherent weakness in the 406 engine when using a Dart high performance block. These engines are built to last. All parts used have much higher hp ratings than this engine is producing.
2. The exhaust note that this engine produces is much deeper than that of any of the smaller cubic inch engines on the market. The difference is dramatic to say the least.
3. This engine can be installed in medium to heavier cars without killing acceleration, having to deepen the final gear, and needing a huge stall converter. This engine will accelerate a 3600 lb or heavier car much better than the 383.
4. Very low maintenance, decent drivability, yet costing only slightly more than building a 383 street rod engine. Horsepower will vary, depending on cam, carb and intake choice. You have up to four different cams to choose from, and two styles of intake manifolds plus two rocker ratios.
5. Longevity, reliability and low maintenance. You don't have to turn the engine to a critical rpm range to produce its max hp output. There is nothing unsafe about running an engine that's as well built as this up to approx. 6,200 rpm. Our NKB aluminum heads use very high quality hardware. The new Dart Super High Performance block would be indestructible if built to the power rating of this engine. The Wiseco Racing pistons are rated at 800+hp. The protection against detonation is at its highest with these type pistons.
6. Should you ever decide to sell your car, the resale value of a street rod with a 406 engine is very desirable compared to those running 383's No 383can be built up to the level of a 406 while running pump gas with the same compression. The power and torque numbers down low in the rpm band are what make the 406 such an incredible engine, compared to the 383.
We do a full test run on every engine we build on a test mule. The engine is run for two intervals of 15 minutes each, and every possible issue is addressed. When you install the engine, you must verify that the timing is set at the correct value, and the fuel to air ratio must be verified. We also include an engine stand like the one pictured, wheels included, and an engine lift plate.
As of 9/15/2013 we completed
installation of our brand new Super Flow 902S dyno. In the past, we outsourced
our dyno work. We were unable to do the research and development we truly
wanted, and this prompted us to make the $105,000 investment. It's been one
of the best investments we have ever made. Every aspect of our engines can now
be monitored, calibrated, and tuned. Best of all, we can now see what combos
generate the best power, with consideration to drivability.
One thing we have noticed is that the
de-tuned engines with different cam and intake combos certainly do have less
top end horsepower than expected, but the torque increase in the low rpm range
is much greater than in the higher horsepower setup. This increase in torque
down low is what you want if you're sporting around on the street, rather than
all out racing. The de-tuned version of this engine will also allow you to set
the car up closer to stock and increase drivability to a very high degree.
Throttle response is also noticeably better.
The build sheet is as follows:
Pictured below is the new Dart SHP block. This block is the absolute ultimate in quality, durability, and value.
Dart SHP block, splayed caps
The block is bored to size with our new Centroid touch probe machine. Few machine shops have a machine of this accuracy.
We also deck the blocks to an RA finish of approx. 15 or better. The decking procedure is also done by our Centroid CNC machine.
We often find many brand new blocks to have a sloping deck of up to 4 thous. When we're finished decking the block, it is within approx. .001 accuracy from end to end. Many machine shops fail to catch this as the machinery they use does not allow for such accuracy.
We then plate hone the block with our new Sunnen SV10 diamond hone machine. This is also a very advanced machine that hones the block with a finish unlike conventional machines.
The final step is to clean the block in our high pressure block washer.
Pictured below is the rotating assembly that comes in this engine.
(file photo, actual parts may vary, see details below)
The photos above and below are file photos. Actual appearance may vary. This picture is to give you an idea of parts used in the rotating assembly portion of this engine. All parts are brand new, first line, unblemished, and balanced in house.
READ THIS LISTING COMPLETELY BEFORE YOU BUY ELSEWHERE!
- Crankshaft: Genuine Scat
- Crankshaft Stroke: 3.750"
- Crankshaft Material : Cast Nodular
- Journal Diameter: STD SBC
- Rear Main Seal: 2pc RMS
Connecting Rod Specs.
- Rods: Genuine Scat
- Rod Type: Scat I-beam, Bronze Bushed.
- Rod Length: 6.0
- Rod Material: Forged 4340 Alloy.
- Rod Bolt/Cap Screw: ARP 8740 Cap Screws.
Piston & Ring Specs.
- Pistons: Wiseco Fully Forged. High Performance for street/strip use.
- Piston Size: 4.155"
- Dome Volume: RD D-cup Dish. Comp. ratio calculates out to approx. 10.5:1
- Compression Height: 1.140
- Piston Material: Forged 2618 Aircraft Alloy
- Piston Rings: Hastings High Performance, Moly, Standard Tension.
- Ring Size and Fit: 1/16 1/16 3/16.
- Ring Material: Cast/Stainless/Moly
Bearing, Damper, and Flexplate Specs.
- Main Bearings: Clevite
- Rod Bearings: Clevite
- Balance: In House on CWT balancer.
- Damper: Pro-Race brand 6.75" Internally balanced.
- Flexplate: Heavy Duty SFI 168 tooth or 153 tooth. Manual Trans. flywheels available.
WISECO FULLY FORGED PISTONS, RATED AT 800+ HP. WISECO PISTONS ARE 100% MANUFACTURED IN THE USA. THEY ARE ONE OF THE HIGHEST RATED PISTON BUILDERS IN THE COUNTRY.
Flat or Dish top pistons will be used depending on Cam selection.
The Wiseco fully forged pistons are rated very high in the street/strip performance industry. They offer several price levels of pistons, starting with the Pro-Tru Street version made with 4032 forged alloy. The next level up would be the Professional series that are much more expensive and made from 2618 aircraft alloy.
Our custom made Wiseco pistons are very close in comparison to the Professional series as they are made using the 2618 aircraft alloy and have fully machined crowns.
We have seen a few engine builders use the
forged 4032 alloy. They may fragment from the effects of detonation
, and we find them to be very risky for any carbureted street rod engine that produces high horse power numbers. We would not even consider using such pistons. Such pistons can allow the connecting rods to destroy the block, crank, and cylinder head. Those types of pistons are fine for stock or mild engine builds, but should never be used in carbureted engines built to high horse power levels. These type of pistons will not stand much detonation. The forged 2618 alloy piston is so much more resistant to the effects of detonation and heat.
Our Wiseco Forged pistons are custom designed with an increase in compression height. This has many advantages. Here are a few facts about compression height and deck height.
Our custom made Wiseco pistons have a compression height that is .015 taller than nearly all catalog pistons on the market. We find this to be a very valuable feature.
Another good feature about our pistons having a taller compression height is that the ring land above the top ring is much stronger by being .015 thicker. When pistons encounter the effects of detonation, it is not uncommon to see pistons with the ring land above the top ring broken off. The thicker ring land also makes a better heat sink.
You may have noticed that our Wiseco custom made forged pistons are referred to as Racing Pistons on the package. This does not mean that the pistons are for racing only. This is a generic term, referring to their ability to be used in high performance applications as well as for street rod use. These pistons are perfectly designed for use on the street, as well as for medium to upper level drag racing.
Our custom made Wiseco forged pistons are made from 2618 aircraft alloy. We find this alloy to be much more suitable for high performance engines than the common 4032 forged alloy. You will usually see the higher end pistons on the market using 2618 aircraft alloy.
Why go with 2618 forged pistons? If you encounter certain tuning issues, detonation is highly probable, and its effects can cause severe damage to your engine. The 2618 forged piston is able to withstand the damaging effects from detonation to a higher degree than the lower cost 4032 forged pistons, especially non-forged hypereutectic pistons such as Speed Pro or Keith Black, and many others.
We have built approximately 3500 engines using the Wiseco pistons. The engines have been for street rod and strip use. We have seen no problems, nor has there been any complaints. They are an excellent product in every respect.
These pistons are also suitable for use with nitrous.
The pictures below are file photos of our Wiseco pistons. Flash glare on the piston top seems to have enhanced the milling marks. These are hardly visible with the naked eye.
The picture below is a generic file photo of a Scat crankshaft.
Some of the benefits of the Scat crankshaft:
The material used in this crankshaft is manufactured from an exclusive Space Age material that was designed for high strength and fatigue resistance. The Scat cranks are the best value you will ever find. The Scat crankshafts are the best way to build a strong bottom end for, street rods, dirt and circle track racing, and drag strip racing.
Pictured below is our ABS crank polishing machine in action. We polish the crank on every engine we build. This extends bearing life, keeps oil cooler, and with the reduced friction, a slight increase in horsepower is gained. Many machine shops fail to do this. The finish on most cranks are at the bare minimum of acceptance, and we know this can affect bearing life. We have measured the RA finish with our profilometer, and found it to be as high as 25 RA finish on many of the cranks. We bring that number down considerably.
We now use the Clevite bearings in our engines.
Our choice of rods are the Scat Pro Stock rods with ARP-8740 cap screws.
We use genuine Scat rods with ARP cap screws in all of our engines. Our Scat rods are bronze bushed, and unlike Eagle I beam rods, these are fully forged 4340 alloy.
We have noticed some engine builders using low cost generic rods
and crankshafts in their engines. These non-branded, (no-name) products are
often poor quality in many ways. You will notice many of the low end engine
builders fail to mention the actual brand of the rods or cranks used in their
engines. Upon further investigation you will find such parts not to be a
branded name product. They may label these parts with a name, but one that is
totally unrecognizable in the industry. Our experience in years past with such
rods and cranks has been disappointing to say the least. Besides the obvious
issues such as incorrect sizing and machining that is difficult to correct, the questionable alloy these items may be produced from and
the potentially incorrect heat treating methods used, could prove to be
disastrous. Little can be done to verify this and nothing can be done to
correct it. Failures
of such critical parts will usually result in catastrophic damage to the engine. As you may have noticed,
this is why we specify the brand name, and series of every part used in our
Many of the inferior "no-name" rods on the market will also have "no-name" rod bolts in them. We have seen these bolts before, and they are very low quality. They don't have ARP's rolled thread design, and they don't torque down with the same characteristics as a genuine ARP bolt. It's not just a matter of having a different brand bolt in the rods; these bolts are low quality in many ways. They have been known to fail in engines to a much greater degree than a high quality rod bolt, and this failure usually causes catastrophic damage in the engine. Beware of rods that don't mention the rod bolt brand. As far as we're concerned, ARP bolts are the only brand we would ever use or accept in a set of rods.
Genuine ARP 8740 cap screws.
PRO RACE BRAND SFI HARMONIC DAMPER, 6.75 DIAMETER INCLUDED.
Pro-Race brand damper is used on all of our engines.
INTERNALLY BALANCED, 6.75" DIAMETER REDUCED ROTATIONAL MASS, OFFERS EXCELLENT CLEARANCE.
1.52" THICKNESS, 2.38" THICKNESS WITH HUB
BILLET ALUMINUM TIMING POINTER. FEW SELLERS FINISH OFF THEIR TURN KEY ENGINES AS WE DO.
We did not offer this billet timing pointer in the past. However, we noticed that there was a birds-eye view of the timing pointer from the driver side of the engine, so we decided to use these on all of our engines.
HEAVY DUTY SFI RATED FLEXPLATE MADE IN THE USA INCLUDED.
This SFI flexplate is made in the USA and will resist cracking and warpage to a very high degree. One good telltale in identifying a low quality flexplate is the lack of welding on each side where the plate mates to the ring gear. They usually have a pale grey color to them, as they are not coated, and will rust quickly. Ours are welded on both sides, and are much thicker than an OE plate, and are zinc dichromate coated.
We do offer this engine with a manual flywheel. In most cases we do have both sizes, 153 and 168 tooth, available.
Our CWT 5500 Balancer.
We do our own balancing with our new state of the art CWT 5500 Series balancers. The CWT 5500 is the ultimate for precision balancing. We now have three of these in our machine shop. We consider this machine to be highly advanced compared to the Hines balancer we once used. We balance every rotating assembly we sell within 2 grams or less at no extra charge. A balance sheet is included with your engine.
Three new CWT balance machines under one roof is a rare sight.
Our crew wrapping up for the day. Pardon the mess.
NKB 200cc ALUMINUM HEADS
Our new NKB-200 heads have been designed especially for us. After receiving many recommendations from our engine builders, we came up with the best quality, best flowing heads on the market relative to cost. The only way you're going to get a set of heads that flow as well or better will be to spend at least double the cost or more. We have installed these heads on all of our 383 and 406 engines for the past two years. Many of these engines were dynoed on our new Superflo dyno. The engines had every possible combination of cam, intake and carb. The results have been amazing. These heads are excellent in design and quality. Our choice of hardware and precision assembly also contribute to the performance and reliability of the heads.
In the flowchart below, the NKB-200s are superior to the Procomp heads in flow rates, and also edge out the Dart SHP heads on the intake side. The intake numbers are far more important than the exhaust. The overall average flow numbers on the NKB-200 heads are higher than most any brand of non cnc'd cast aluminum heads on the market.
The difference in horsepower and torque generated by the NKB heads is monumental compared to most all of the low cost sbc heads on the market. We offer several different cam choices with our 383 engine.
Here is a rundown on the hardware used in the NKB heads and the assembly process.
The retail cost at most High Performance stores on the PBM Competition valves is $239
We are now using the Competition Series PBM valves in all of our 383 and 406 engines. These are considered a high end valve. These valves have an undercut and backcut feature.
The backcut feature reduces valve weight by an average of 12.5 grams per valve. This weight reduction of approx. 208 grams off the complete set of valves has a monumental effect on acceleration, deceleration, and valve train life. It may be difficult to understand how this works, but rest assured, this is a huge reduction. The valve spring compression and rebound action will remain stable for a much longer time running lighter weight valves, as well as reducing valve float.
The backcut feature is not be mistaken for undercut. These valves have both features. Backcutting is an additional radius, but located on the head of the valve to increase the flow numbers and reduce valve weight. The flow increase is approx. 3-6 points on the flow bench, and possibly more, depending on the initial flow rate of the heads.
According to one of our machinists who built Winston Cup engines for 15 years, the exhaust valves had an additional radius cut on the outermost edge that allowed a better escape of the exhaust gas. This cut on the exhaust valve is in addition to the back-cut feature. The competition series are made from a much higher temp alloy than most other stainless valves. There are at least three levels of stainless valves on the market, excluding those used in very high level racing such as pro-mod. The PBM competition series is compared to the highest level of those three. As a final note, backcutting a set of valves is said to improve flow in the low lift area, and this is most desirable on street rods.
Comp High Performance Dual Springs, Part Number 987-16
Our Comp springs are 1.43 diameter, with an inner spring and internal damper. Others are using springs that are much smaller in diameter. Smaller diameter springs may be in the correct spring pressure zone, but they usually have a shorter life. Comp springs are made in the USA. All of our engines using the NKB heads use these springs. Spring failures are near non-existent.
COMP CAMS "POSITIVE STOP" VITON VALVE STEM SEALS. # 529-16
Comp 10 degree machined valve locks.
We use only Comp Super 10 degree machined locks. Our head builder noticed the low grade locks on the market fit more loosely than he felt they should, not to mention the possibility that they were made of inferior metal. He envisioned the engine being much more prone to dropping a valve at high rpm. Using these locks, we have yet to have an engine drop a valve due to a valve lock failure.
Comp Cams retainers # 75740-16 and Comp Cams ID locators Part number: 4771-16
Our Comp Cams retainers # 75740-16 and Comp ID locators # VTH-4771-16 are made from 4130 chromoly steel. These retainers have a perfect fit with the Comp valve locks. We have used these on all of our engines for many years, and have had zero failures.
We hone all of the bronze valve guides with a ball berry flex hone to establish not only perfect clearance, but also a semi cross hatch finish for oil retention. We finish off with a natural bristle brush. The heads are then placed in our parts washer and cleaned with high pressure hot water, then pressure dried. Before installing the valves, we apply a heavy coat of engine assembly lube to the valve stems. The coating on the valve stems is essential to protect the bronze guides from gaulding on initial startup.
Our next step is to set the spring pressure to a predetermined pressure using a spring height checking device, most suitable for street rod use. The springs we are using allow for a near perfect seat to nose ratio. Be warned that some sellers of aftermarket heads may not be checking the installed height when assembling the heads, and may not be setting them up to the correct pressures. We have a full scale machine shop with several very knowledgeable engine builders that know and fully understand how to properly assemble a set of heads. Combine the possibility of poor assembly methods with incorrect or low grade hardware, and it is easy to see how failures can result.
Head gaskets are Fel Pro 1003 premium race grade series, and ARP head bolts, and rocker studs.
Comp Cams High Energy Aluminum Roller Rockers.
If you've read our warning on engine builders using low grade no-name rods and cranks, a similar situation exists in the roller rocker market. We do not use or sell non branded, (no-name) roller rockers, period. They have proven to be faulty in many ways. The center trunnions are not polished, nor is the center of the roller tip true to size or polished. Metal fragments are often left inside the trunnion housing and will cause destruction of the needle bearings. The pins and keepers that hold the parts together are often of poor quality and improperly installed. The front roller will usually scoot along the valve tip, as it can't roll properly due to rough internal surfaces.
We have honestly seen valve tips that were scalloped out due to the front roller dragging across them. This will cause the valves to side-load against the valve guides in the heads and surely cause damage to them if run like this for very long.
We have scrutinized these products in the past and found all of the above problems, and I can tell you there are most likely many more. We would not use them in an engine under any circumstances. You will also see many of these rockers made from stainless on the market. They use a low grade stainless that actually has a near non-existent amount of nickel in them, but that's not the real problem with them, as stainless steel has no advantage over high grade heat treated steel when it comes to a roller rocker. The lack of hardness of the rocker body is the real problem. The problems with these stainless rockers are the same as mentioned above. These are the roller rockers you see on the market for around $119 and up to $169 for the so called stainless ones. They are pure junk, in our honest opinion. They could possibly be used on a budget back yard stock build up that has a very low spring pressure, with a cam that has very low lift, but then you would be better off with the stock stamped rockers on such a build.
We have heard of many engines using these rockers that came apart and spilled needle bearings into the engine, only to end up in the oil pump. It seems like some engine builders do not care how long the parts in your engine last, or they simply don't know this. I can tell you for sure that using such low grade, "no-name" roller rockers is asking for trouble.
We use Comp High Energy, Comp Ultra Pro Magnum, Comp Gold Arc, Scorpion Race and Endurance Series rockers in all of our engines. The difference in these compared to the low grade no-name rockers on the market is huge.
Howrds Tie Bar Lifters or Delphi Anti Pump up lifters. Depending on Cam Choice.
We have had a vast amount of experience with the Dehphi hydraulic roller lifters. They are a good quality lifter and work well in our engines.
Howards Brand Chromoly One pc. Pushrods.
Howards brand are the only type of pushrod we use in our engines. Made in the USA from 4130 chromoly steel. Regular hardened pushrods will most likely flex in the engine when running above normal RPM ranges, and risk bending under high RPM. These do not have the welded ball on the end. We only use the swedged one pc. design, which is a well proven design far superior to the style many others use in engines. 4130 chromoly steel is also much stronger, and will resist flexing. When a pushrod flexes in the engine, you lose lift. Don't be misled by the term "hardened," as this is nothing more than a stock style low cost push rod. They will flex in the engine or possibly bend permanently.
We are offering several cam choices listed below in this engine. Read the specs carefully.
Cam choice # 1
Howards part no. 180345-10
Valve lift with 1.5 Rockers: Intake .565/Exhaust .580
Duration @.050": Intake .245/Exhaust .253
Lobe sep. angle: 110º
This cam is the most aggressive of the four choices listed. It will make its peak horse power at approx 6350 rpm. The idle is radical.
We recommend a stall converter of around 2750-3000. Final gearing would need to be at 373 or numerically higher. A 373 final gear is most optimal with this cam, providing the car is reasonably light. This cam does make the most horse power but will trade off bottom end throttle response and low speed cruising in the low rpm range unless your car is setup in pro-street form. The idle sound with this cam is very erratic.
You would not be able to run an overdrive trans, power brakes, or air conditioning with this cam choice. Valve train life and reliability is reduced with this cam as compared to the other choices. This would only be a concern for those wanting to drive their vehicles on long trips or with frequent use. This cam choice puts your setup nearly into the Pro-Street league.
Drivability is fair at best with this cam, unless you have a very light car, with a decent final gear.
If your car is over 3400 lbs, we strongly advise against this cam, unless you have a final gear in the 4.10 range or numerically higher. If you're on the fence with this cam choice and the one below, then you may want to go with this cam and keep the rocker ratio at 1.5, or go with cam choice 2 and go with a 1.6 ratio. That would put you somewhere in the middle of cam choice 1 and 2, at least in respect to valve lift.
Below are our dyno results on one of our 406 engines with cam choice # 1 with a single plane intake. You results may vary depending on intake choice. The horse power numbers will always improve anywhere from 5-10 more than what the dyno results show after the rings have fully seated.
Official Dyno report on our 406 engine with cam choice #1, flat top pistons, and a single plane intake.
The flat top pistons are not what comes with this engine, as it puts the compression ratio on the very high side for pump gas. This dyno certainly shows the potential of the 406 engine with the added compression ratio. The compression ratio is the only difference done to this engine that increased the hp numbers. This put the compression numbers in the mid 11's. Having the compression in the mid 10's will allow the engine to make hp numbers in the 540 range with cam choice 1, and a single plane Hurricane intake, 1.6 rockers.
Official Dyno report on our 406 engine with cam choice #1 and a single plane intake.
Cam choice #1 and a single plane intake.
If you choose cam choice 1 with the single plane intake combination, it is highly recommended that you upgrade the ignition system to an MSD Pro Billet distributor, and CDI unit. You should also upgrade the carburetor to the SS Series for optimal performance. These important upgrades are essential for improved idling and overall performance. If you do decide to use the MSD Pro Billet distributor we suggest you use the black timing degree bushing to increase the initial timing and possibly the lighter springs to control how soon the total mechanical advance comes in. You may even "lock-out" the distributor, depending on you cars overall setup. The CDI unit will make a huge improvement in how the engine runs at idle. Low speed cruising will be greatly improved, as well as high rpm operation. The SS carb upgrade is an all out double pumper carb, and gives the engine instant throttle response. If you choose cam choice 2 you may not require these upgrades but should consider them to enhance the performance and drivability of your engine.
There is one more upgrade that I feel would enhance overall performance and add stability and longevity the valve train. The Max Effort Tie bar lifter upgrade is essential for those that choose to run hard. We use the regular Howards tie bar lifters with this cam and they do well, but the Max Efforts have proven to be much more stable in the upper rpm ranges. Any over-revving of the engine beyond it's peak power may bring on valve float when using the regular tie bar lifters. The Howards Max Effort Tie Bar lifters will not only improve performance but also allow the engine to operate very well in it's peak rpm range and beyond. This is a very nice upgrade for any street rod running into the upper rpm ranges.
Cam choice #2
PART # 180265-10
Valve lift with 1.5 Rockers: Intake .530/Exhaust .545
Duration @.050": Intake .233/Exhaust .245
Lobe sep. angle: 110º
Cam choice 2 is considered somewhat aggressive and improves drivability compared to cam choice 1. This cam will still have a lopy idle. You would require a stall converter in the 2500-2800 range.
Final gearing should still be at approx. 3.73. If your car is in the 3800 lb weight range or more, we recommend cam choice 3 or 4. Hp numbers will drop with this cam, around 20-25 at the most. Combine this cam choice with the dual plane intake option and hp numbers will fall approx another 10-15, but bottom end torque is greatly improved, as well as drivability.
It is not recommended to opt for the single plane intake if your car is in the medium to heavy weight range. They do not operate as well in the lower rpm range. The low end torque with this cam comes in sooner than cam choice 1, but you must still set the car up with proper gearing and converter stall. This cam is our most popular and delivers great bottom end power and very good drivability.
You may not be able to run an overdrive trans with this setup, power brakes are a possibility. We do not recommend this cam if your going to run an A/C unit. Our cam choice 3 or 4 would be much more suitable.
Below are our dyno results on one of our 406 engines with cam choice # 2 with a dual plane intake. You results may vary depending on intake choice. The horse power numbers will usually improve anywhere from 5-10 more than what the dyno results show after the rings have fully seated.
Official Dyno report on our 406 engine with cam choice #2 and a dual plane intake.
Cam choice #2 and a dual plane intake.
Listed below is is a single plane intake setup with an AFR head upgrade. As you can see the hp numbers are considerably higher.
Cam choice #3
PART NUMBER: 08-000-8-11480
510/525 lift with 1.5 rockers
230/238 duration at 50%
111 lobe sep.
This cam choice (3) is the perfect all around setup for those wanting excellent bottom and mid range power, while still generating decent power at the top. Horsepower rating would drop an additional 10-15 hp below the cam choice 2. Drivability and street manners would be considered excellent. Heavy cars, upwards of 3800 lbs or more, would do well with this cam choice. No need for a high rpm stall with this cam, but you would still require a stall in the 2200-2500 rpm range for optimal acceleration.
If your car is in the heavy weight range, and/or geared on the steep side and you want much better streetability, then this is the correct cam choice. You still want to keep the final gear ratio at approx. 3.20 or numerically higher. If you have an overdrive trans., then this cam, coupled with the dual plane intake, would allow the engine to cruise in overdrive with rpm in the 1950-2050 rpm range. Should you have a Turbo 350 trans, then this cam choice would allow you to run a somewhat taller final gear to allow decent highway driving in the lower rpm ranges.
You may choose 1.5 or 1.6 rockers with this cam, but we recommend the 1.5 rockers for even better low end response, especially if you plan on running an overdrive transmission. You can also expect a much longer valve train life with this cam compared to the larger cams listed above, especially with the 1.5 ratio rocker choice.
Carb size when using this cam will drop. You'll notice slightly better mileage and better throttle response with this carb versus the larger carbs required when running the larger cams. If your vehicle is very heavy, over 4400 lbs, then we recommend our cam choice #4.
Official Dyno Report in a 406 engine with this cam, NKB heads, dual plane intake, Quick Fuel SQ-750 carb, and HEI distributor.
Official Dyno Report in a 406 engine with this cam, NKB heads, dual plane intake, Quick Fuel SL 750 carb, and HEI distributor.
Official Dyno Report in a 406 engine with this cam, NKB heads, dual plane EPS intake, Holley 750 carb, and HEI distributor.
Cam choice #4
Valve lift with 1.5 Rockers: Intake .465/Exhaust .470
Duration @.050": Intake .209/Exhaust .215
Lobe sep. angle: 110º
Cam choice #4 would be an excellent choice for those with a heavy car or truck. This cam would also be the best choice for those running a 700R4 trans. Low speed cruising, running an A/C, and excellent vacuum for operating power brakes are all possible with this cam.
Great off idle power. A stall converter in the 1600-2250 range would give excellent results. Gearing could be considerably taller, allowing for much better mileage and low rpm highway cruising.
Excellent of idle power is what to expect from this cam choice. Carb size will drop once more with this cam. Possibly better mileage, and for certain, throttle response would be excellent with this cam. Valve train wear and noise would be nearly nonexistent when coupled with 1.5 or 1.6 rockers.
One more benefit of this cam choice is that we can set the engine up with a reduced compression ratio, and this would offer great protection against detonation, and also extend the life the of engine. Running mid grade fuel or even regular grade fuel becomes a possibility with the reduced compression ratio.
The information above on cam selection is not etched in stone. You could step outside these guidelines in either direction to some degree and still have very good street manners. The larger cams could possibly cross the finish line sooner in cars that are setup properly compared to the smaller choices, but the smaller cams will have a better feel in the lower to mid rpm range without all the drama of the more radical setups above.
We're all hungry for as much horsepower as we can get, but building an engine of a given size to higher horsepower will always require a trade off. The 383 engine offers the best of both worlds when it comes to bottom and top end power, but the bigger cams are more demanding on gearing and stall, sensitive to weight, and suffer on drivability as well as valve train wear and tear.
THE FOUR CAMS LISTED WILL COVER MOST NEEDS FOR ANY STREET ROD OR SPORT TRUCK.
QUICK FUEL SLAYER 600-750 CFM CARB, DEPENDING ON CAM CHOICE.
Quick Fuel Technology (QFT) has engineered its new Slayer series vacuum secondary street carbs with all the features. The Slayer is not some stripped-down off-shore QFT copy, it features the same QFT race engineering, all-aluminum construction and hand-built quality that goes into all QFT race-winning carburetors.
The Slayer's incredible value is made possible by QFT's new CNC machining centers and the unique design that utilizes a secondary metering plate with changeable jets, eliminating the costly secondary metering block unneeded for most street/strip cars. The majority of fine tuning on a street carburetor is done on the primary side, and the Slayerâ„¢ provides all of the popular options: changeable idle air and high-speed air bleeds, 3-stage emulsion circuits, changeable primary idle feed restrictions and power valve restrictions.
A truly welcomed feature is the QFT QuickSet adjustment on the vacuum secondary diaphragm that provides a quick external twist adjustment without changing springs. Secondary metering can be altered with changeable main jets and the secondary float is also notched for jet extensions.
Additional features are a fully adjustable electric choke, and a semi polished finish that will improve any engine compartment. The Slayerâ„¢ 750cfm (Part # SL-750-VS) features a 1-11/16" throttle bore and a 1.375" venturi.
You have a choice of single or dual plane intake. The single plane intake (1st pic below) should only be used on cars that are very lightweight and have good hood clearance.
Dual Plane Intake shown below. This is a large runner dual plane intake. They make excellent mid range power.
Polished intakes also available.
Pictured below is the Edelbrock Performer EPS dual plane intake. If you're going with cam choice # 2 or 3 and require more bottom end power, we strongly recommend this intake. This intake offers incredible low end response and has excellent hood clearance for those installing this engine in a C3 Corvette with a non-cowl stock hood.
304 STAINLESS ALLEN HEAD INTAKE BOLTS ARE USED ON ALL OUR ENGINES.
Pictured below are some of our most popular valve covers. They are fabricated aluminum, and very high quality. You may select from any of the valve covers we have listed at no additional cost for your engine.
The satin covers below are by far the most popular.
RETRO STYLE FINNED. OUR SECOND MOST POPULAR CHOICE.
THE RETRO FINNED VALVE COVERS CONTRAST NICELY WITH THE CHROME AND POLISHED ITEMS.
OUR RETRO STYLE TALL FINNED VALVE COVERS HAVE BECOME VERY POPULAR. YOUR CHOICE.
Timing components: Cloyes Race Billet double roller timing set.
Polished Aluminum Timing Cover.
We use the top of the line Cloyes timing set. The difference in quality is dramatic compared to the common true double roller setup. The chain is made in Germany and the sprockets are hardened billet steel (upper and lower). These sets are hand matched for selective sizing.
The cost on this high end timing set is approx $135.00, about three times the cost of the low level budget timing set used by many other engine builders. Should you ever want to confirm that this is what is actually in your engine, you can remove the timing cover, and you will see that this timing set is very different in appearance to the run of the mill low cost sets often used by others.
This top of the line timing set is offered in three different chain tension setups, allowing us to set it up perfectly every time. One more benefit is that timing accuracy is very precise and will remain that way. This timing set will likely last for the life of the engine. This is what you will find in most solid roller engines, as they have very high spring rates, and create an enormous load on the chain and gears, compared to non solid roller setups. It may seem like a bit of overkill to use such a high end timing set, but the versatility and extreme quality outweigh the cost, in our opinion.
Melling M-Select Oil Pump, and M-Select Drive rod with ARP stud.
The M-Select series oil pump by Melling has several important upgrades compared to the regular Melling M-55 Series. The gears are billet steel, and the body is stronger, coated with corrosion-resistant nitrite. This oil pump also includes the M-Select drive rod. Both components are far superior to the regular Melling oil pump and drive rods used by most other engine builders.
Champ premium oil pan.
Pictured above is the oil pan included with this engine. The Champ oil pan used on this engine has an 8 qt. capacity. It has an elaborate oil control system. Features windage tray, crank scraper, .055 gauge outer shell, with reinforcing ribs. Champ oil pans are made in the USA. All QRP Series engines will come with the Champ oil pan. If your car will not allow the use of the large capacity Champ oil pan, we have the same series pan in stock appearing form. 5qt. capacity and still has the windage tray, and crank scraper.
We do not use the knock off oil pan gaskets on the market. Felpro premium oil pan gaskets are used on all of our engines.
We use this premium studded mini nut set for oil pan and valve cover fasteners. The nuts have a serrated face and built in washers. This is the ultimate set for securing the oil pan to the engine and is far superior to the typical bolts used by most other builders. We use this set on all our engines.
Listed below are more of the items installed on the outside of the engine, which makes it a "Turn Key" engine.
If you chose cam choice 1 or 2, then we highly recommend using an exhaust evac. system. The vacuum created by the engine is somewhat insufficient when using these larger cams, heads, carb and intake to operate a pcv system at its best. The exhaust evac system will pull the crankcase gases out of the engine at a very smooth and controlled rate. This allows the rings to seat in much faster and better, and can increase horse power to some degree by reducing crankcase pressure. Another benefit of the evac system is that you're not contaminating the fuel and air mixture with semi-burned byproducts from the engine oil and combustion process.
After the engine is completely broken in, the pcv setup may be sufficient. However, it may not be the best choice. The break-in time may also be slower with the pcv setup.
We also offer a vacuum pump system for the ultimate in crankcase pressure control.
If you do decide to use an exhaust evac system, we have a few more recommendations. The bullet style perforated mufflers, like those made by Magnaflow and many other companies, must be used. In our opinion, they sound the best and, most importantly, they allow the exhaust evac system to work properly. Magnaflow is a popular brand of the true straight through mufflers, and there are several other brands on the market such as Corsa, Borla, and Bullet. The sound level is controlled by the length you choose. The 12-16 inch length sounds the best to us. These mufflers have smooth perforated inner walls. They should not be confused with traditional glass packs with fluted walls, which are very restrictive and have a somewhat sloppy sound.
Traditional chambered mufflers, like Flowmaster, create a back pressure pulse that will interfere with the operation of an exhaust evac. system. Chambered mufflers have the reputation of helping bottom end throttle response, but you will have a decent amount of bottom end power with this engine, especially if you have chosen cam choice 2, 3 or 4. In our experience, the straight through perforated mufflers sound and perform better in every respect, and allow the proper use of an exhaust evac. system. More info. on this subject below.
If your vehicle is a pre 75 model that came with a point style distributor, then you should opt for the full size HEI dist with the OE style cap, not the Super Cap. Both distributors are identical, but the OE style coil cover does allow a slight more firewall tunnel clearance. Some models may not even allow the use the OE style HEI distributor. If you think you are going to encounter this problem, then you may choose our MSD Pro Billet ditributor and CDI system. It has a small base and is identical in size to the original point style distributor. It will require the use of an externally mounted coil, and CDI unit. This type ignition system is far superior to an HEI distributor in many ways.
The plug wires are included but not installed on the engine. Due to the many different style headers being used, we will send the universal wires with the engine for custom fitment.
TAYLOR SPIRO PRO SERIES 8mm UNIVERSAL IGNITION WIRES, 90 DEGREE BOOTS AND OUR 65K VOLT HEI DISTRIBUTOR ARE INCLUDED.
The distributor will be installed in the engine.
· Spiro-Pro 8mm Wire is the top choice of racers and enthusiasts due to its affordable value and overall high performance features.
· Spiro-Pro's two-layer 100% silicone inner core & outer jacket keeps the wires flexible for the life of your vehicle, maintaining its vibrant color with heat protection to 600º F.
· Taylor Cable's Spiro-Pro wire consists of a high conductive spiral wound core with a Stainless Steel wire and covered with a fluorocarbon conductive material.
· Spiro-Pro features 350 ohms per foot resistance which provides more fire power to the spark plugs than OEM resistor core wires and has up to 10 times less resistance than standard resistor core wires.
· Spiro-Pro eliminates radio frequency interference (RFI) and is recommended when using a multi spark discharge, electronic ignition systems and other electronic components.
· Features Taylor Cable's EXCLUSIVE low profile 100% silicone PROBOOTS® with vibration proof Stainless Steel double spring locking spark plug terminals.
· These are Universal Fit sets and will require cutting to fit, terminating, and booting the distributor end. Universal Fit sets are universal for most American made vehicles.
We include an engine lift plate and heavy duty engine stand with casters with every engine we build.
We offer this engine with selected upgrades. Listed below are some of the most requested ones. Many not only improve performance, but further enhance the reliability and longevity of your engine, along with resale value. Most of these upgrades are low in cost considering the benefits they offer.
Flywheel upgrade/option for manual transmission. Upgrade to a 168-tooth or 153-tooth flexplate for manual transmissions.
Cost for this option is $105.00 We have this upgrade/option featured in our other listings. There will be a 153 tooth and a 168 tooth size available. Be sure you know the size you need. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
SFI Billet Steel flywheel upgrade/option for manual transmission. Upgrade to a PRW brand billet steel flywheel SFI rated 168-tooth or 153-tooth for manual transmissions. We highly recommend the SFI billet steel flywheel for those running hard. These are fully cnc'd and far superior in many ways compared to the regular cast iron flywheel.
Cost for the SFI billet flywheel option is $169.00 We have this upgrade/option featured in our other listings. There will be a Chevy 153 tooth and a Chevy 168 tooth size available. Be sure you know the size you need. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
SFI damper: Offers an extreme level of safety against breakage, and is very resistant against slippage of the elastomer damping material. SFI dampers are not only made from a better grade of steel, they are also constructed differently and have a much better appearance. They usually last much longer than a non-SFI damper. Many drag strips require this on engines producing high horse power levels. The SFI certification is laser etched into the side.
Cost of the SFI damper upgrade is $69.50 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
Scat Competition Rods: Recommended for those running hard. The regular Scat rods that come with this assembly are sufficient for most street rod uses, but the Scat Competition series rods offer more security against rod breakage under hard use, and they have the huge ARP-8740 7/16's cap screws. The Competition rods have a 600+ Hp rating, and the slight cost to upgrade is well worth it in our opinion. These rods require slightly less cam to rod clearancing then the regular Scat rods. We use the very same Scat Competition rods in our 600+ hp 427 and 434 engines.
Cost of this Scat Competition rod upgrade is $65.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
ARP-2000 rod bolts: This is one upgrade that we find to be very valuable. The rod bolts are most likely to fail under hard use, moreso than the rod itself. When a rod bolt fails during high RPM, total engine destruction is usually the result. The ARP-2000 rod bolts are a very good upgrade, in our opinion. We actually have few, if any, problems with the regular ARP-8740 bolts, but those who run hard always upgrade to the ARP-2000 rod bolts. The ARP-2000 rod bolts also torque at a higher number, and this increased clamping force is also a factor in keeping the big end of the rod stable and true to size. The ARP-2000 bolts are installed in the rods and this upgrade is only available with the Competition rod upgrade.
Cost of this ARP 2000 rod bolt upgrade is $85.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
Race balancing: This is for those who want the engine to operate virtually vibration free at high rpm. Extends engine life and frees up a few more horse power. This is a somewhat labor intensive procedure and is not required, but the feel of an absolutely vibration free engine at high rpm is desirable by many. The standard balance job that is included with this assembly at no extra charge is certainly sufficient. With a race balance job, all pistons and rods are match weighed to within 2/10's of a gram or less, and the final balance is brought down to around 1 gram plus or minus. An ultra smooth engine at high rpm has a noticeable feel and sound to it. If you do not opt for this upgrade, the assembly will still be fully balanced. We spend a good hour and a half doing the regular balance work, and it will certainly meet your needs.
Cost of this race balancing upgrade is $125.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
Scat 4340 Forged Crank: The forged Scat crank has a rating of 800+ HP. This is the ultimate upgrade for those wanting to run hard. Nos, blowers, turbos, are not an issue with this crank. Even without such power adders, this Crank offers great protection under the most severe conditions. This upgrade also comes with the HP high Performance King bearings. Should you decide to run power adders in the future, this would be essential. The fatigue life of the 4340 crank over the cast nodular is also greatly extended. We do offer this upgrade as part of many of our assemblies in some of our other listings. They have the key words, "fully forged," in the title.
Cost of this forged crank upgrade is $460.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
Internal (neutral) balanced front. This low cost upgrade is the next best thing to an internal balanced crank. This Scat crank is similar in design to the one offered in this assembly, but it has an internal (neutral) balanced front. Running a crank that is neutral balanced in the front will allow the use of a non-weighted front damper. This will eliminate the additional mass from a weighted damper. Replacing the damper, if it's ever needed, becomes a simple procedure, and assures that the balancing is not affected. It's well known that under high rpm conditions, the front of the crank on externally balanced engines is at risk of breaking much more than those with an internal setup.
Cost of the internally balanced front crank is $49.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
Polished single plane or dual plane Intake Manifold: This low cost upgrade really adds beauty to the engine for those who like the bright polished look on the engine. This is available on our Single plane or large runner dual plane intake, known as the Eliminator (very similar to the Edelbrock RPM Airgap).
Cost of the polished single or dual intake is $49.50 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this assembly you may add any of these upgrades to your shopping cart. Click here to add upgrades.
Single plane or dual plane Speedmaster polished intake upgrade, your choice.
Dyno Tuning: This is one of the most important upgrade/options we offer. There are many benefits to this service. The engine is first run at fast idle to bring the water and oil temp up to normal operating temperature. It is then run for approx. 20 minutes under a simulated load at around 3k rpm to promote initial ring seating. After this, the engine is shut down to allow us to check the readings on the spark plugs, and for any possible oil leaks. This cool down is considered part of the engine's first heat cycle. We then follow up with multiple low to medium rpm runs to further the break-in process of all the moving parts in the engine. During these multiple runs, we are paying close attention to the EGT, (exhaust gas temp) readings, vacuum pump readings, oil temp and pressure, coolant temp, and overall engine sound. At this point, we start the actual dyno tuning process and this focuses around the air to fuel ratio numbers and what timing numbers produce peak power. We usually have to change carb. jetting several times, adjust the idle circuits, and the air-bleeds occasionally have to be changed. We then establish the engine's full horse power and torque numbers at a given rpm limit.
Having your engine dyno tuned will allow it to run its absolute best, and is very important in protecting the engine from potential damage caused by the carburetor running excessively rich or lean. This also establishes the engine's hp output and max rpm. These numbers are very important to know. There is one more value we consider just as important to what we have mentioned above. An engine that has been dyno tuned has also been validated to be in perfect operating condition. This is something that running the engine on a test mule can't provide. Any problems the engine may have will show up during the dyno tuning process. We have on rare occasion seen a popular combination show hp numbers that were not where they should be. Some of these problems give no indication other than reduced hp numbers. We find and fix such problems. The problem may be something simple and easy to find and in some cases very difficult to pinpoint. We will not send the engine out until it's perfect. If you choose not to purchase the dyno tuning package, we will still do a test mule run, as many engine builders do, and it certainly is better than nothing but pales in comparison to a full dyno tuning. When engines are dyno tuned, the chances of you having a problem are near non-existent. Unforeseen problems may still, occur but they are rare. We have kept the cost on this extensive procedure low to not only make it affordable, but it gives us great peace of mind knowing the engine will be in perfect operating condition when it is received. The cost to do a repair once the engine is installed can be very expensive for both us the seller and the customer. When you see the final dyno run of your engine on youtube, consider the fact that approximately five man hours, around $25.00 worth of fuel, oil and filter and $105K worth of dyno equipment went into making that one minute final test run video.
Cost of the full dyno tune option is $350.00 We have this upgrade featured in our other listings. You can see this and other upgrade options in our ebay store under the "UPGRADES" category, or simply do a search with the key word, "Upgrade" in the search bar when shopping in our ebay store. Before you finalize your purchase of this engine, you may add any of these upgrades to your shopping cart. Click here to add upgrades.
Pictured below is one of our actual Super Flow dyno's. This is a 2016 model and highly advanced compared to the much older models many shops have. We have two of these in use at our shop.
The Super Flow is the best dyno in the industry.
If you purchase a starter from us you will have to install it. There is no way for us to properly shim the starter (should it be needed) while the torque converter and transmission are not installed. The flexplate will change position when the transmission is installed and the torque converter is hooked up to the flexplate. Some flexplates have a slight amount of run-out/warpage when the trans. and torque converter are not connected to it. This makes correct starter installation difficult. Only when you have the torque converter mounted to the flexplate can you properly install and adjust the starter.
Suggestion: While the engine is out of the car, still mounted on the engine stand, bolt up your torque converter to the flexplate. This will flatten out the flexplate to a great degree. Then, mount your starter on the engine. This is the only time you will have a birds eye view of the starter gear and ring gear from the back of the engine. You can see ifthe proper amount of mesh is there.
It's possible that once the transmission is installed and the torque converter is hooked up to the flexplate, the position of the ring gear may move a slight bit more. The transmission shaft centers up to the torque converter, and this causes the flexplate to further change shape slightly. This may alter your initial starter adjustment, and if it does, you may need to do a light adjustment once the transmission is installed.
We strongly suggest using our Powermaster 9100 or 9400 starter on this engine. These starters have proven to be highly reliable, and offer excellent header clearance.
IMPORTANT NOTE ABOUT DE-TUNING.
For those with very heavy vehicles, such as 4x4 quad cab trucks, 3/4 ton trucks, and crew cab/ex-cab trucks, Suburbans, plus trucks that may do light to medium trailer towing, we recommend the de-tuned version of this engine.
For those wanting to run a supercharger, we recommend our extra deep dish pistons with the 75cc heads regardless of the vehicle.
Our machinists each have many years of experience in building racing engines. This very critical work is done to exacting specs and with great care. Many vendors do not have machinists with the experience or the proper equipment that we are fortunate to have. We have built engines that cost upwards of $50,000. All of our engine builders have been in the engine machining and engine building line of work for their entire working lives. Their ages range from 40 to 67. We have a total of seven machinists/engine builders.
We have dyno tested the original creation of this engine with every cam and intake choice available extensively. We now include the engine test mule run at no additional cost. The engine is thoroughly tested for leaks, vibration, unusual noises, overall engine sound and feel.
THIS ENGINE IS BUILT WITH THE BEST AVAILABLE PARTS WITH CONSIDERATION TO KEEPING THE COST OF THIS ENGINE REASONABLE. WE'VE REVIEWED WHAT THE COMPETITION IS OFFERING, AND WE'RE CONVINCED THAT WE ARE OFFERING THE BEST VALUE FOR THE MONEY.
This engine has a Two Year Warranty with unlimited mileage.
- Should a major problem arise with this engine within the first year of use, the warranty covers all parts and labor and we will pay for shipping the engine both ways.
- Keep the crate your engine came in to ensure a safe return to our workshop.
- We do not cover the removal or re-installation of the engine at any time during the warranty period.
- Our engines must be used with a rev limiter. Should warranty issues arise, proof of the rev limiter use will be required.
- Should a problem occur in the first year of the warranty that we determine can be repaired by you or a qualified repair shop, upon our written approval, we will pay for the repair based on our in-house hourly rates for labor and our estimate of a reasonable amount of time to make the repair with the engine on a stand as you received it. To be specific, due to the difficulty of accessing certain engine parts in some vehicles, we are not responsible for the additional time and labor costs you may incur in removing and replacing such parts.
- In the second year, the warranty will cover all parts minus any labor to remove and install needed parts. The cost of shipping the engine to us is not covered in the second year of warranty.
- Tuning or maintenance are not covered under the warranty. Tuning includes jetting or adjusting the carb, ignition timing, or readjusting the rockers. Tuning would also include changing out plugs to optimize temp range for your needs. Setting ignition timing is also considered tuning. You must check the timing on this engine before it is driven.
- If you are not satisfied with the cam or intake you have chosen, we will exchange any of these items for up to 60 days. You will pay for shipping and any required labor.
- Damage due to overheating, detonation or extreme abuse will not be covered by the warranty. Detonation damage is evident upon removal of the cyl. heads.
- Engines used in marine applications will have a limited warranty of 1 year. The first six months will cover parts and labor, and the second half of the one year period will cover parts only. Marine engines must upgrade to a 4340 crank unless the engine already comes with this, and the ARP-2000 rod bolts.
You can enjoy your engine with occasional spirited driving, as it is well designed for it, but we will not cover damage caused by racing or improper tuning. A rev limiter and fuel to air ratio monitoring device must be used on this engine. The rev limiter should be set to cut off at its peak horsepower or less if you choose, and this should allow many years of service without a problem.
Your carb should be tuned to allow the correct fuel to air ratio. This ratio can vary depending on many factors such as altitude, vehicle weight, gearing, type of driving, etc. These values should be in the recommended safe zone.
Continue reading for more detailed information on timing and carburetion. You must follow the recommendations listed below.
Tuning, maintenance, and oil recommendations.
This engine must be maintained with oil specifically designed for high performance engines. The life of the engine can be greatly extended if you run a race grade engine oil such as our Schaeffer brand racing oil. We strongly recommend the Schaeffer Micron Moly 20w-50 grade in warm to hot weather. You may use the lighter weight Schaeffer Supreme 7000 series semi synthetic oil in cooler weather. After the engine is fully broken in, you may move over the Schaeffer full synthetic oil. The Schaeffer brand oil is very highly rated. It is the only brand of oil we use when dyno tuning. Racing oil must be changed more often than conventional oil. Every 2000 miles or less would be optimal.
We offer a full line of this oil in our other listings.
Rather than using mileage as an indicator of ring sealing, it's better to use oil consumption as a guide.
Oil pressure low as 50-60 lbs in the upper rpm range on a fully warmed up engine is nothing to worry about. You may also notice that oil pressure drops at idle to approx 25-30 lbs when the engine is fully warmed up during very hot weather. This is somewhat common and no cause for alarm.
The Dart block used in this engine has priority main oiling. This block routes the oil in a different pathway compared to a GM block. The mains and rod bearings as well as the crankshaft are well protected with an ample supply of oil even when the oil pressure numbers are lower than you think they should be. Oil pressure in the filter can be very high when the engine is cold. You must always allow the engine to warm up before any hard acceleration.
There are many special additives in race grade oils that are not in conventional oil. These additives are very valuable for high performance engines. Never add anything to racing oil. This oil has exactly what is needed to protect a high performance engine. Some of these oils will state that they are low or possibly non-detergent, and that is a desirable trait of racing oil.
The anti-foaming agents in race grade oils are much better than what you would find in conventional motor oil. Race grade oils have higher than normal amounts of the zinc compounds in them, and there are many components in the engine that can make great use of these additives.
If you are running a mechanical fuel pump on our engine, you absolutely must follow the oil guidelines to the letter.
We recommend running an electric fuel pump on this engine due to the higher than normal eccentric cam lobe failure rate experienced with engines running a mechanical fuel pump.
The high volume mechanical fuel pumps put an additional strain on the eccentric fuel pump lobe on the cam, and modern roller cam technology may not be addressing the eccentric cam lobe design like it once did years ago, since very few people are running mechanical fuel pumps anymore and the roller cams and lifters do not require these special treatments.
Modern oils further the problem due to the absence of high levels of the zinc compounds they once had. These factors can spell doom for the eccentric fuel pump lobe on the cam in these engines. Use the oils we recommend to avoid such problems.
If you insist on running a mechanical fuel pump, then using a race grade oil becomes essential. To further protect the cam, we offer a special fuel pump rod made from an ultralight material. It's made from a proprietary blended, carbon reinforced, bearing-grade polymer. This fuel pump rod only weighs 25 grams, and is very strong yet gentle on the eccentric cam lobe. If you do decide to use a mechanical fuel pump, we strongly recommend our Quick Fuel line of mechanical fuel pumps.
Unlike the common light weight hollow rod on the market, this rod is one third the weight, and a bit more costly. By reducing the reciprocating mass of the fuel pump rod, the load on the eccentric cam lobe is greatly reduced. We offer this rod in our other listings.
As for oil filters, we recommend AC Delco, selected K&N, Moroso, or any of the other high quality oil filters on the market.
The Wiseco forged pistons that we use are not made from the low expansion 4032 alloy material. Ours are all made from 2618 Aircraft alloy. This type of alloy has a greater amount of expansion in the bore until fully warmed up, but not as much as some of the all out race pistons. Nonetheless, they do have more clearance until warmed up. Therefore, let the engine warm up before accelerating all out. You should start up and go at a mild driving pace for around 10 min. or longer.
You must use a rev-limiter on this engine. Should you have a warranty issue, proof that you have one will be required. A rev-limiter will allow you the freedom to drive without having to monitor the tach. Every car from the factory has this feature. Set the limiter to the peak hp rating of this engine or less for added protection.
You must run a crankcase ventilation system to pull gases from the crankcase. This is not supplied with this engine. We have these in our other listings. Usually a pcv system will work, but due to the erratic engine air speed, it may not work so well. We recommend an exhaust evac. system with the larger cam choices. After the engine is totally broken in, you may possibly be able to convert back to the regular style valve cover breathers and pcv system.
If you run the exhaust evac system, then you must have straight through mufflers such as the ones made by Magnaflow, Corsa, Borla, and Bullet, etc. These mufflers have perforated walls and flow straight through. These type mufflers will allow the exhaust evac system to gently pull gases from the crankcase at all times at a smooth consistent flow. Your engine rings will seat much faster. Regular chambered mufflers will interfere with the operation of an exhaust evac system.
One other benefit of using an exhaust evac system is the reduction in oil leaks. Excessive crankcase pressure is the cause of many oil leaks. After the rings have fully seated, the crankcase pressure will reduce considerably and oil seepage or minor leaks that may have been present will usually stop. We strongly recommend the Moroso brand exhaust evac system over any of the other brands on the market. They have a patent design that others do not use in the tubes that go into the header collector. The fluted notch in the tubes creates a much better drawing effect than those without it.
If you decided on cam choice three with this engine and have chosen our dual plane intake, the common pcv system may be sufficient, but we still would like you to use the exhaust evac setup at least until the engine is fully broken in.
Educate yourself on the exhaust evac. systems before using them. You will find plenty of great information on the internet about them.
Engine break in: As soon as your engine is installed, check and reset the timing if needed. Get the car on the road as soon as possible, and run the engine in a somewhat aggressive mode, not exceeding 4,500 rpm for the first few hundred miles.
Drive safely please; we're not asking you to drive fast or aggressively. Just keep your engine under load more than normal. Drive it in a very inefficient manner. Keep the engine with load against it, and bring the rpm up and back down to seat the rings much better and faster. This allows the rings to expand in a perfect circle and with greater pressure against the cylinder walls to establish an even wear pattern.
If you have opted for our dyno-tuned version of this engine, then ring seating will be partially established. The dyno has a computer controlled break-in mode that we use before doing any dyno testing for power output. Should you opt for the dyno tuning package, it does not mean that your engine is ready for synthetic racing oil. Your engine will continue to seat the rings in to an even higher degree after 300-500 miles of driving, and crankcase pressures will continue drop.
VERY IMPORTANT NOTICE.
This engine does not come with oil in it. The oil that was used during the test run or dyno tuning will be drained as this is required by the shipping companies. We also prefer draining the oil as this gives us a chance to examine it for metal particles. The filter is removed and is also closely examined for metal particles or debris. To prevent oil from dripping onto the shipping pallet, we re-install a new low cost regular spin-on oil filter.
You must prime your oil filter. Priming is not needed when changing oil on a well broken-in warm engine that has been running moments before changing the oil. Your new engine that has been sitting around for weeks, if not months, MUST be primed.
You should replace the oil filter that comes on the engine with a brand that we recommend, but opt for the medium length version, as this will help maintain oil pressure and volume much better than the short version.
If you have chosen our Champ stock appearance pan, fill it with approx 5-6 qts. of oil.
If you have the extended capacity Champ pan with kick outs then you will use approx. 7.5-8 qts of oil. Just remember to fill/prime the oil filter with oil before starting the engine.
Tuning recommendations. Very important.
You must be sure that your air to fuel ratio is correct. We strongly recommend purchasing a fuel to air ratio monitor. Proper carb jetting is also a must.
If your carb is running too lean, detonation is at your door.
If it is excessively rich, cylinder wash-down from excessive fuel will destroy your bore finish, pistons, and rings quickly, not to mention cause excessive fuel consumption.
A tad on the rich side is not a problem and can help resist detonation; a tad on the lean side will generate the most power and increase fuel mileage.
The optimal air to fuel ratio is approx. 13:1 Set total timing at 30-34 degrees. Total timing refers to the reading at 4500 rpm with the vac. advance disconnected. The closer to the lower number (30 degrees) the total timing is, the safer your engine will be. Do not worry about initial timing, as it will be determined by the total timing.
You may try running the vacuum advance if you have our regular HEI in this engine. Cam choice 1 may not allow proper operation of this, but the smaller cams may work well. The vacuum advance is adjustable and we recommend that you try it out. If you feel the vac. advance is putting too much initial timing into the engine, you should be able to adjust some of this out of it. Most aftermarket HEI units have an adjustable vac. advance. When setting the total timing, do not have the vac. advance hooked up. If you can bring your initial timing up from where it is at idle by running the vac. advance, the engine will operate tremendously better, have much better fuel mileage, and run cooler in most vehicles. Being able to run the vac. advance with good results is dependent on many factors.
If you hear valve clatter/ping (as it's called), then you need to try and adjust this out of the vac. advance. If valve clatter (pinging, as it's also known) is present under load, then you may not be able to run the vac. advance, but if the valve clatter is coming in around 3500 rpm or higher, then this could be a sign your total timing is set too high. Try backing it off a few degrees before giving up on the vac. advance. Valve clatter/pinging is actually the sound of the detonation occurring in the engine, and can be very damaging.
Be sure to have a high amperage battery and high quality starter. The battery must be 850 cca or more. Use heavy gauge battery cables. If you have a hard cranking issue, purchase an in-car timing controller or ignition kill switch. This will allow you to control your timing for optimal performance and ease of starting.
Do not run regular gas in this engine, no matter how much you have reduced the timing. It may not be enough! You may have run an old car in the past that pinged and clattered under load for many miles, and this didn't seem to hurt it. Most cars from the 60's and 70's had very low compression, especially when nearly worn out, and this is why the detonation did not destroy the engine. Excessive pinging or valve clatter, as it's often referred to, may destroy this engine very quickly. Light pinging now and then is unlikely to do any damage, but it certainly will when there is an excessive amount of it under load.
Let any engine with compression numbers above 10:1 clatter and ping for very long, and you will lose the engine due to detonation, and in some cases this can happen very quickly.
Spark Plugs: We recommend the Autolite brand, part number Autolite 3923. Most of our engines include the correct spark plugs. We also offer a premium NGK plug that is highly suitable for this engine when running in very hot climate. Race grade plugs are fine as they have a few features that are desirable for certain types of driving. Keep the temp in the low to middle range. Use a plug that's too hot, and you are once again close to detonation/pre-ignition; use a plug that's too cold and they will foul constantly, run poorly when cruising at low speed, and be difficult to start.
Some of our engines come with spark plugs in them, depending on the package you purchase. You may also use NGK part # NGK 4544, a plug that is one step lower in heat range than the Autolite plug. The NGK plug is only to be run during very hot weather.
You would be amazed at how much better an engine will run with the correct spark plugs installed, but brand name has little do with this. It's more to do with heat range than any other factor. Factors such as outside temp, altitude, compression ratio, and the type of driving you do determine the temp range to run.
A slight loss of power is also an issue with plugs that are too cold, as well as possible difficulty in starting. However, you can have much more serious issues by running plugs with high temp ranges.
Keep the engine coolant temp as low as possible, but it is not a problem if it runs as high as 210 on very hot days, as long as it's consistent, and not climbing.
Never use pure antifreeze. 50/50 mixture or even slightly less antifreeze will cool the engine better than a rich mixture of antifreeze. Keep the engine temp down if possible, but don't worry if you can't get it below 210 on a hot summer day. The cooler you keep the engine, the lower the risk of detonation. Set engine idle at approx. 900-950, and never too far below this unless you are running our cam choice three. The reduced size cams would allow for a lower idle speed.
If your carburetor is not functioning correctly, it can ruin your engine. If your carburetor size is more than one step in either direction from the recommended size, it can cause an imbalance in the fuel to air ratio, and be nearly impossible to tune.
Proper jetting is also a must. Never let the engine idle for excessively long periods during the break-in period.
Do not overfill with engine oil. Slightly less than normal is better than too much, in most cases.
When setting your carb choke, we recommend setting it on the mild/lean side. It is best for the choke to open up to its full straight up position as quickly as possible. Keep backing it off until cold starting becomes difficult. If you are running an electric fuel pump, then the Q-Series Quickfuel carbs are best to run. They are also suitable for use on engines running a mechanical fuel pump. They do not have an electric choke system, and this is usually not a problem unless you are running the engine is extremely cold weather.
If the choke is set up on the aggressive side, it will create an over-rich condition upon every cold start-up and warm-up. This over-rich condition is very damaging to an engine, and will waste fuel.
If you feel you can get by without a choke, then by all means do without it! The modern day carbs actually do well with very little or no choke. With a few pumps of the throttle and a bit of feathering the throttle will have you off and going smoothly, in most cases with very little or no choking at all.
Valve train maintenance.
Hydraulic roller setups are virtually maintenance-free and very long lived compared to a solid roller setup.
Our recommendations will change from time to time. We never stop trying to build a better engine, and we learn from our own experiences and from feedback from our customers. We know there's always room for improvement. We're always working on research and development, as does any successful business. We advise checking out the recommendation section of our engine ads on a regular basis.
Why have we given such detailed information on our warranty and maintenance suggestions? Some customers bought our engines and did not fully understand our warranty and the maintenance needs of the engines.
Not knowing is understandable, but failing to educate yourself on the do's and don'ts is asking for problems. We suggest joining a few good car forums, as they have a wealth of great information.
However, beware of individuals on forums who think they know it all, and really know very little. Do your research using several sources, and be sure to read between the lines.
This engine does not include a fuel pump. This engine is best suited to operate with an electric fuel pump, with a pressure regulator set at 6-6.5 psi. A 125-130 gph rated pump should be sufficient. It's best not use a higher capacity fuel pump than required. A chrome block off plate will be installed on the engine. We believe that the electric fuel pump system is a superior fuel delivery system compared to a mechanical system.
Your engine info will include the balance sheet and other information on this engine such as cam card, and your invoice will show your personal selection of the options offered.
Many have asked why we're able to sell such an engine for such a great price. It's because we're a major distribution center for all of the parts used in this engine, as well as a full scale machine shop. Our purchase price for the parts used in this and all of our engines are at master warehouse distributor (WD) pricing. Few machine shops ever get to master-wd pricing. We also believe in keeping our profit levels low enough to allow the working man a chance to build his car the way it should be built.
Your selection of what type transmission you're going to use with your new engine is very important. I'm going to give you the real lowdown on what transmissions I recommend, as well as the ones I would stay away from. For those building a very mild, (detuned) street rod, (small cam choice, dual plane intake) these recommendations are not as critical.
700R4: Worst possible transmission choice.
- None, other than there are plenty of them around for a cheap price, and for good reason.
- Fuel injection does make this trans. more tolerable.
- It will get you from point A to point B period!
- Very wide first to second gear spread. First gear is a 3.06 ratio Second is a 1.62 ratio. This nearly equates to skipping from first to third gear with a manual trans. This kills acceleration when these trans go into second gear on a carbureted engine with a healthy cam and large runner intake manifold. Compare this to a TH350. First gear at 2.52 ratio and second gear is 1.52 do the math.
- The 3.06 first gear is so low that any final gear of above 3.55 or numerically higher will have you right at the max rpm at around 35 mph, only to then have your car fall on its face when it hits second gear, feeling like it skipped a gear. Wheel spin is uncontrollable upon hard launches, unless you have a very tall final gear, and then you can for sure count on going nowhere quickly when second gear comes in. Overdrive would be totally useless at highway speed regardless of detuning with a tall final gear, unless you were cruising at around 100 mph.
- Huge cost to build up to a decent street rod level. Don't even consider a stock rebuild to handle 500 hp or more. Under hard use, the 700R4 will fail quickly.
- Limited as to what level these can be built up to. High performance transmission builders and parts suppliers don't even recognize this as a serious transmission.
- More complex to build than a TH350 and far more expensive, especially when built up to handle high hp numbers.
- Having to run a cumbersome throttle value cable to the carb. linkage. This feature actually serves a good purpose, but if not set properly, it can destroy your transmission quickly. Very critical adjustment, and often overlooked.
- The overdrive is actually useless with engines running decent size cams relative to the cubic inch, especially with large runner dual plane intakes, and single plane intakes are out of the question with this trans.
- Stall converters are double the cost of the one run in a TH350.
- This is not a reliable transmission in a street rod.
- Lowers the value of your vehicle to some degree, especially on high hp builds. These transmissions do not belong in most carbureted street rods. You must detune an engine considerably to operate the overdrive and be able to tolerate the first to second gear drop.
- Could be classified as the worst mismatch of parts known on a true street rod.
- As a side note, I would like to mention that most of us have owned a regular stock street car with a 700R4 trans, or its electronic likeness, a 4L60E, and didn't find much of an issue with the way they operated, especially if the vehicle was fuel injected. This is because stock car engines are designed to operate totally different in the very low rpm range. They have huge amounts of off idle torque compared to the average carbureted street rod that makes 400 hp or more. This off idle instant torque allows the vehicle to keep its speed up decently when the 700R4 drops into second gear, and the same low rpm also allows the overdrive gear to operate normally at very low rpm. There are other factors that also allow these trans. to operate at low rpm, especially on fuel injected computer driven engines.
TH350: Best transmission choice, hands down.
- Excellent gear spread between all three gears.
- Very low cost to build up to various levels of power handling.
- Can be built up to extreme power handling capabilities.
- Most all transmission shops are capable of building these to at least level 1 or 2.
- No TV cable to deal with.
- Stall converters are low in cost, and the selection is broad.
- Very reliable and simple to repair if needed.
- None, simply none! Select a final gear that will allow you the best overall performance and one that allows a decent off the line acceleration, and one that will be in a tolerable rpm range at highway speed. You must have the correct stall converter for optimal performance. This can make a huge difference in the way your vehicle accelerates.
- These are becoming scarce, but there are still plenty of them around, and high performance parts are easily obtained.
- You may have to go through this long story to your less than knowledgeable friends as to why you didn't choose a 700R4, and when you explain it to them, they may still think you don't know what you're talking about.
- Excellent gear spread. Very similar to a TH350.
- Strong internal parts.
- Simple to build or repair to stock buildup levels.
- Very expensive to build up to higher power handling levels, as compared to a TH350. The TH350 has far more high performance parts available at reasonable costs. The 400 trans. is not a practical choice.
- Internal rotating parts (cast iron drum) are very heavy and create a huge drag compared to most any other trans., and this is not a subtle amount of drag. The TH400 is well known to be a heavier duty trans. than a TH350 but this heavy duty factor was designed more for heavy vehicles that may encounter pulling heavy loads. Only the largest of the GM cars weighing around 5000 lbs had these trans. in them, along with heavy duty pickups, usually 3/4 ton or larger trucks. Even the half ton Chevy trucks didn't come with these in them.
- They will certainly hold up better than a stock built TH350, but they are not a desirable trans. for a street rod. You can build a TH350 to level two that would be superior to any stock TH400 in every way for about the same cost. Building a TH400 to a high hp handling level will cost a great deal of money.
- You will never see this trans in a true Pro-Street car.
- Excellent transmission to build up to just about any power handling level.
- Most trans. shops are able to build this trans with ease.
- Very reliable, and simple to work on. Not much to go wrong.
- Decent first to second gear spread.
- Rotational drag is very low with this trans., moreso than any automatic on the market. Very efficient trans.
- Stall converters are not expensive and many choices available.
- Two gears, that's the problem. This trans. can only be run in cars that have a very high hp to weight ratio. It would be fair to say a vehicle weighing approx. 3400 lbs would require an engine output of 1000 hp or more to make it a rational choice, and even then, you would still need a decent final gear to get things moving off the line. The first gear in these is somewhat tall. Those running a T-Bucket roadster weighing around 1800 lbs. with a 500 hp or higher engine could make great use of a Powerglide trans.
- Having only two gears limits having the best of both worlds when it comes to off the line acceleration and cruising at highway speed.
- Has a better gear spread than the 700R4 but not as optimal as the TH350.
- Not much good to say about this trans. It certainly has a place in some special late model applications, but old school Chevy engines is not one of them.
- This transmission can cost up to three times more to build up to a decent power handling level compared to a built up TH350.
- Cannot hold up to high torque engine builds unless an enormous amount of money is spent on this trans.
- Most all the cons you see for the 700R4 exist within this trans.
- This trans is not a reliable trans. compared to any of the early GM trans.
4L60E Electronically controlled trans.
- No TV cable to deal with or shifting linkage. It has pump pressure control and shifting via electronics.
- Not much good to say about this expensive trans. It is virtually a 700R4 with a modern twist.
- Most of the same issues as the 700R4. Terrible choice to run in an old school carbureted engine.
- Very expensive to build up to a high power handling level. Can cost up to $4,000 to build this trans up to a decent level. Computer controlled engines may require this unless you bypass the car's computer system.
- Complex. Very complex!
- Pointless to run such a terrible transmission.
- If you insist on such a trans, the 4L80E is a better choice, as it has a normal gear spread, and is a much stronger trans. Still pointless to use with an old school carbureted engine.
Four and five speed Manual Trans.
- Excellent acceleration at any speed due to many selective gear ratios. Finding a gear at any cruising speed to hit it hard is easily accomplished with a manual compared to an automatic.
- More efficient delivery of horse power to the rear wheels with a manual trans. versus an automatic. In other words, less loss of power due to slippage as encountered with an automatic trans.
- For some people, the fun factor of shifting gears is one of the high points of owning a street rod.
- Very reliable, long lasting. Low maintenance. Simple to change out a clutch if needed.
- Can be very expensive to purchase a high quality modern manual trans. and high performance clutch and flywheel, especially the Tremec Series.
- Can be somewhat complex to change over from an auto to a manual trans.
- If you think your car is going to run faster with a manual versus an auto, you will be greatly disappointed. The automatic transmission can not only shift much faster, but off line acceleration can be controlled to a much greater degree. This is why most drag cars have automatic transmissions. All things equal, a car equipped with an auto trans will outrun one equipped with a regular street rod manual with great ease.
- Missing gears when racing can cause damage to your engine, and loss of control of your vehicle should you drop into the previous gear during an aggressive run. Been there a couple times, dropped a valve in brand new Lotus Esprit shifting out of second into first rather than third, and locked up the back wheels on a Dodge Viper shifting into second rather than fourth at high speed. Nearly lost control of the car at around 80 mph.
- If you're deciding to run a 5 or 6 speed manual trans because of the overdrive gear, be aware that most engines built with large lopey cams, and single plane intakes running a carb will usually not allow effective use of the overdrive gear.
- Tremec T56 transmissions are very popular and highly advanced. They are expensive. They tend to be notchy to shift when new. Takes many miles before they become easy to shift. They can be difficult to install in some early model classic cars, as they are huge compared to early model transmissions. They can cost a great deal of money to rebuild if needed. Still about the best manual trans out there, and can handle very high hp levels.
- Sadly, your wife may not be able to drive your car with a manual trans. This could be a plus in some cases.
A final note.
Our eBay user id is: skipwhite, and our eBay store name is whiteperformance1. You may have noticed other sellers using a similar name offering similar products. These other sellers have capitalized on our name as we see it, and many customers searching for us will inadvertently find them, thinking we are one in the same company. There is only one "Skip White" We are the original premier eBay seller under this name since approximately 2002. We have no other eBay names, nor are we associated with any other company regardless of the similarity in the name or location. Our official company name is Skip White Performance.