AFR CHEVY SBC 406 421 434 ELIMINATOR HEADS 210cc 75cc FULLY BUILT # 1050-HR-75
|Product Type||Shipped Product|
|Number of reviews||0|
AFR 210cc RUNNERS 75cc CHAMBERS ELIMINATOR ALUMINUM HEADS. Angle Plug. FULLY CNC'd
AIR FLOW RESEARCH
This sale is for a fully assembled set of heads (2 heads).
The springs in this setup are to operate with hydraulic roller cams up to .600 lift.
READY TO INSTALL.
PICTURED ABOVE ARE OUR FULLY CNC'D AFR HEADS.
The AFR heads are the best aftermarket cylinder heads in the world. Quality, performance, and reliability are excellent.
Below is the flow chart for the AFR 210cc heads. The flow numbers speak for themselves. A cam in the 500 lift range on up to around 600 lift would be a very good match for these heads.
As our company founder explains it, the results you experience with the AFR heads will vary greatly by what type setup you are running. The engine combos we have dynoed are what most people have chosen to use as far as cam and intake selection goes, and we have some of the results listed below. The engines dynoed with the 210cc heads were mostly sbc 421, 427, and 434engines in the 10:1 to 10.5:1 compression range, give or take. We also did an aggressive 406 build with the 210 heads. Normally, we use the 195cc heads on the 406 but found the 210's suitable due to the cam size of this one particular engine. All run on pump gas.
Our 421 through 434 engine ads have a selection of four different cams and these engines all come with AFR heads. This has given us a great opportunity to see how they performed. We were able to test several different cam setups with these heads. This will give you an idea on what these heads are capable of with a given combination of cam, intake, rockers, and carb. This may also help you select a proper cam for your build.
We feel the 210cc AFR heads would perform very well on a medium to aggressive 421, 427, or 434 build or a somewhat Pro-street 406. As mentioned, below is just an excerpt from our 421-434 ads. If you're using a lower lift than those listed below, then it would be fair to say the hp will drop, but not by much, providing your lift and duration are somewhat close to any of the cams mentioned below. This will give you an idea of what kind of power to expect with these heads, and it can certainly help you choose a cam and intake.
Please do understand that a cam is not included with the heads. This is just a guide to show what you may expect with a given combination when building your engine.
PART # 186755-10
Valve lift with 1.5 Rockers: Intake .600/Exhaust .581
Duration @.050": Intake .251/Exhaust .255
Cam choice #1 with AFR 210cc heads
This cam choice # 1 is somewhat aggressive in the 421 through 434 engines with the addition of the AFR 210cc heads. We topped it off with a set of 1.6 rockers, and went with the Hurricane single plane intake, added the Super Sucker plate, and produced an amazing 625 horse power at 6300 rpm with 550 lb ft of torque at 5200 rpm. This test was done on our sbc 434 street rod engine on pump gas. The other engines mentioned have done very close to this with the same heads and cam package. These numbers are very good for not having to run the rpm any higher than this. The horse power numbers are very accurate. We performed the testing on our new Super Flo 902s dyno. No question that the numbers are correct, as we have been spot on with all of our other dyno tests of engine combos that we knew what to expect from past dyno records. The drivability, as it's referred to, would be considered decent with this setup in a medium weight vehicle (3200-3500 lbs).
Part # 180345-10
Valve lift with 1.5 Rockers: Intake .565/Exhaust .580
Duration @.050": Intake .245/Exhaust .253
Cam choice #2 with the AFR 210cc heads
This cam choice (2) in the 421-434 engines with the AFR 210cc heads is the perfect all around setup for those wanting a very good bottom and mid range, yet still making excellent power at the top. This engine will use the same compression as the cam choice above. Horsepower rating would drop approx. 30-35 hp with this cam. Bottom end power comes in much sooner, and this cam smooths out around 2200 rpm. This cam will make its peak power at approx. 6000 rpm.
If your car is in the medium weight range or up to approx. 3,700 lbs, and you're wanting slightly better streetability, then this is a good cam and head choice. You still want to keep the final gear ratio at .323 but no more than a .355 would be needed for great results on the street. Keeping the gear ratio on the tall side is more acceptable with this cam compared to the other choice mentioned above. You may choose 1.5 or 1.6 rockers with this cam, but we recommend the 1.5 rockers for better low end response.
This cam should be paired up with the dual plane Crosswind intake for better drivability. The single plane Hurricane can be used, but the dual plane will have much better bottom end and mid range response. Our test engine used the single plane intake. The dual plane intake would drop peak power by about 15 hp over the single plane intake. Bottom end response would be better with the dual plane. You can also expect a longer valve train life with this cam compared to the larger cam choices.
Official dyno results on our 427 Stage 5.2 engine with this cam, AFR 210-75 Heads, a QuickFuel 750 carb, and a dual plane intake.
Official dyno results in our 434 engine with a Comp Cams 520/540 cam, these heads, our new Brawler carburetor, and a dual plane intake.
An excerpt from our engine ad about our new dyno.
As of 9/15/2013 we have completed installation of our brand new Super Flow 902S dyno. In the past, we have outsourced our dyno work. Never being able to do the research and development we truly wanted, prompted us to make the $105,000 investment. Needless to say, it's been the best investment we have ever made. Every aspect of our engines can now be monitored, calibrated, and tuned. Best of all, we can see what combos make the best power, with consideration to drivability.
One thing we have noticed is that the de-tuned engines with different cam and intake combos certainly do have less top end horse power, as expected, but the torque increase in the low rpm range is much greater than the higher horse power setup. This increase in torque down low is what you want if you're sporting around on the street, rather than all out racing. The de-tuned version of our engines will also allow you to set the car up closer to stock and increase drivability to a very high degree. Throttle response is also noticeably better.
A final note...Skip White Performance...About Us
I'm sure many of you have noticed there are 2 high performance engine builders in Kingsport, TN with similar names, leading to a great amount of confusion.
We are Skip White Performance, NOT White Performance and Machine.
Due to the name similarity, many customers looking for us online inadvertently find them, thinking we are the same company. Definitely not...there is no connection between the two companies. We don't have a problem with free enterprise (competition). However, when the competition builds their foundation on such things as a name similarity and their supposedly long history of being in business, then we think it's about time we set the record straight.
We have owned White Performance since 2003, with the exception of the machine shop, which was owned by Fred White at the time. He continued to operate the machine shop and build engines for us while we continued selling online under the user ID of skipwhite and the store name of whiteperformance1.
Due to their limited production capability and many disagreements about the engine and head building process as well as workmanship, we opted to open a full scale machine shop of our own a few years later. Fred White began competing against us even though our contract had a non-compete clause in it.
As our business grew, we opened a second, much larger warehouse and machine shop around 2011, located on Brookside Ln. in Kingsport TN. By putting heart and soul in this company, we have become the number one street rod engine builder in the nation.
Fred sold his shop to an investor in 2016 and the new owners continue to reap the benefits from this confusion between the two shops. This investor lacked any knowledge of this industry. They continue to use the White Performance & Machine name. Contrary to what is posted on their website, Fred White is no longer associated with the company in any way. Their main spiel in advertising is, "In business since 1979," when in fact, we purchased the White Performance company in 2003, with the exception of the machine shop.
All in all, we have been in this business going on 17+ years. Skip White's passion has been owning and building street rods for 47 years on a personal level. The knowledge he has gained over time has allowed him to venture into this business and succeed to a very high level.
The great pretenders continue capitalizing on our success due to the name similarity, but have been degrading our reputation. We have been getting calls nearly on a daily basis from people that now realize there are two shops in this town with very similar names. Customers complain of serious problems in getting their orders in a timely manner from them. They think they purchased their cylinder heads from us. Due to the confusion, there is an increasing amount of negative feedback that is affecting our name within the street rod community, when in fact we have a near perfect reputation in this industry. We have an "A+" rating with the Better Business Bureau and we have maintained the A+ rating for many years.
FAST FORWARD TO PRESENT DAY...We have become the largest street rod engine builder in the nation. Our engines, rotating assemblies, and cylinder heads are built to very high standards and shipped to our customers in a timely manner. We are a premier seller on with a positive feedback score of well over 206,000 and growing, as compared to our competitor’s score of approximately 24,000.
Our engines are custom-built to our customers' specifications and are shipped in approx. 2-5 weeks, perhaps sooner, depending on the season. Our rotating assemblies usually ship out in about one week or less, and our heads ship in about a week or less.
This product does not have any reviews yet.