SBC CHEVY FABRICATED TALL ALUMINUM VALVE COVERS NO ACC. HOLES 6350-S
|Product Type||Shipped Product|
|Number of reviews||5|
SBC CHEVY TALL ALUMINUM FABRICATED VALVE COVERS. NO HOLES. LONG BOLT STYLE, HARDWARE INCLUDED.
The welding is first class. The billet rails on these valve covers is approx. .225" thick. The aluminum sheet metal is approx. .075" thick. We know many on the market to be much thinner in these areas. This is why many other sellers fail to mention these specs.
This is a very good quality set of valve covers. Beware of others offering similar valve covers for a lower price. The quality is most likely inferior. Fit and finish are often compromised.
These valve covers have a somewhat low luster satin finish. We find many of our customer to like the satin/brushed look. We have sold thousands of these over the years, and all have been satisfied with the finish. The valve covers do have a very nice luster to them. We mention the term, "brushed" finish. The valve covers do not really have an actual brushed finish, but they have a similar appearance to metal such as brushed stainless.
Part number 6350-S
The long bolt style valve covers can be difficult to install if a special procedure is not followed. You must start each bolt with no more than a half turn into the threaded holes in the cylinder head. The welded tubes in the valve covers that the long bolts go through are usually not in a perfect line with the threaded holes in the cylinder head. These tubes usually shift slightly when welded to the frame work on the inside of the valve cover. By starting each one of the long bolts with no more than one half turn, you will be able to move the valve cover into position to allow each one of the other bolts to start into the threaded holes in the cylinder head. After you have all the bolts partially screwed into each hole in the cylinder head, you should not have a problem screwing each bolt all the way into the threaded hole in the cylinder head. Each tube will draw itself into the exact position, and the tubes will stay in the correct position even when the valve covers are removed. If you start any of the long bolts with more than one half turn, then there is a great chance you will run into a problem. The intense heat from the welding is what causes this. We have experienced this with all long bolt valve covers on the market.
We have used these valve covers on thousands of our high performance engines for over 10 years without any issues. On occasion, you may notice a slight degree of warpage on the rails before installation. This is due to the heat generated by the massive amount of welding done around the outer edge of the rails. This warpage is not a problem. When the valve covers are bolted on, they will pull down flat and seal well. Any micro amounts of variation left over after you have bolted them down will be compensated for by the gaskets. Any and all fabricated valve covers with such welding on the rails will have this characteristic. It's simply not a problem in the least. We dyno many of the engines using these valve covers. The engines are brought up to considerably high rpm levels, and rarely do we ever see any signs of oil seepage. They seal very well. The extra thick valve cover gaskets we use do an excellent job of sealing around the valve covers: Part number 7483-ET. See our other listings for these. Every engine we build uses the extra thick gaskets.
When we dyno a brand new engine, the crankcase pressure is higher than normal until the engine rings seat. This causes the oil to seep from any possible exit on the engine, such as around the valve covers and gaskets. We had always used our regular black neoprene gaskets on the engines but on occasion had to use the extra thick ones due to stud girdle clearance with certain heads. Our engine builders noticed that the extra thick valve cover gaskets had virtually zero seepage as compared the regular neoprene gaskets. As we see it, the extra thick gaskets are the key factor in eliminating seepage. Extra thick valve cover gaskets also give the engine a more pronounced (wide/tall) appearance.
The finish on these valve covers may on occasion have very minor cosmetic flaws on them. In the world of mass production, it's to be expected. The massive amount of welding on the rails can sometimes leave small spatter marks in some areas. You may also see very minor scratches in the finish. These flaws are only noticeable upon close observation. Once mounted on the engine, these very small cosmetic blemishes are not noticeable from a distance of several feet. In most cases, the valve covers are flawless or nearly flawless. There are some very high end fabricated valve covers on the market that cost four to five times as much, and on those you may even find minor flaws, but it's less likely due to their extreme cost. As mentioned above, you cannot see these minor flaws from the normal viewing distance standing in front of the car.
These valve covers are 3.45" tall on the inside not including the valve cover gasket. Most vc gaskets on the market are approx. .175" thick, and this brings the total height to 3.625". There are extra thick gaskets available that will bring the height to approx. 3.75", and will certainly clear most any stud-girdles and roller rockers on the market with ease. Our Gold Series stud girdles have oversized bars that are wider then most and these valve covers do clear them with ease with the use of the regular .175" thick vc gaskets.
The rocker studs used in our engines are the ARP long version as that is what is required for the huge/thick Comp High Energy rockers, and topped off with the over sized stud girdles including the tall poly locks had no clearance issues for these valve covers. We have used over 1500 sets of these or similar style valve covers on our sbc engines, and used as many 5 different popular styles of roller rockers and yet to have an interference issue. This is not to say you will never encounter some interference with certain rockers on the market, but the Comp High Energy rockers, and the huge Scorpion race series have given no problems and they are far from small in size. It would be fair to say that there are few if any roller rockers or stud girdles on the market that will give you a problem with these valve covers. The picture below is one of our engines with the large Comp High Energy rockers and our over sized stud girdles that will be topped off with a set of these style valve covers. Also notice that we have the stud girdles set high up on the on the poly locks and clearance is still not a problem. Our engines all use 200 long valves, with 1.46 diameter springs. This makes valve cover fitment even more challenging. The valve cover gaskets we use are normal thickness, but in some instances you may encounter a fitment issue and the use of thicker valve cover gaskets becomes an instant cure in most cases. AFR heads will require the thicker valve cover gaskets due to the higher than normal spring pocket height.
The best set of valve covers on the market, and at a closeout price.
See our other listings for valve cover accessories.
Pictured below is an engine we built with a similar set of valve covers that have the satin finish on them. This will give you an idea of what this finish looks like on an engine. The valve covers on the engine are the short bolt style. You will receive the long bolt style.
From ebay user ebay_user (deleted account)
Reviewed by ebay_user (deleted account) on June 13, 2021, 1:49 a.m. | Permalink
This review has no votes.
From ebay user 9***k
Reviewed by 9***k on June 9, 2021, 4:40 a.m. | Permalink
This review has no votes.
From ebay user s***r
fast shipping item as described
Reviewed by s***r on May 28, 2021, 9:03 a.m. | Permalink
This review has no votes.